Hello Guest it is January 27, 2022, 07:27:20 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Mr.Horsepower

Pages: 1
General Mach Discussion / Re: laser software
« on: December 11, 2012, 01:20:13 PM »
plastic plywood wood acryl cardboard ruber... wood

but this work must use engraving plastic

I use co2 laser

General Mach Discussion / Re: laser software
« on: December 11, 2012, 11:12:00 AM »
someting like that....


photo and text and cutting off

General Mach Discussion / laser software
« on: December 11, 2012, 04:54:01 AM »
what I can use with mach3
I need engraving image and text  cut out plate same work And of course easy use and visual :)

General Mach Discussion / Re: laser setings
« on: November 21, 2012, 12:13:45 PM »

what it is M10P1 / M11P1 Macro or simple command ? turn on /off like  m3 /m5

or can I rename m3 /m5 command and its works ?

I found your homepage and read that... gode ok

but how i get use
or can I rename m3 /m5 command and its works ?

I found your homepage and read

but how use that step for step

or can that call example z axles gode turns on and off command

General Mach Discussion / Re: laser setings
« on: November 20, 2012, 06:24:04 PM »
if I don't want use m3 code

what then else way make laser beam control ?

 now I use pin 2 control laser beam and output#1 this works wery well if run vector cut like plasma cut ok

but not raster picture engrave
but if I want cut raster picture how I make setup

may can be possible My relay it too slow???
that is why this setup does not work
but if I make circuit transistor switch connect 3 wire

1 cut data

2 laser ground

3 laser drive voltage

but if I solder direct 2 pin wire (db25) and that´s connect  transitor and swicts on laser beam ?
and connect  transtor switch on wire 2 and 3 and this make laser beam this correct setting

If I use a digital trigger what should I do to make this works
stage by stage

of course set  digital trigger on and use and inputs set what that use pin example now pin 2 in my setup

but what else...

General Mach Discussion / Re: laser setings
« on: November 15, 2012, 09:37:50 AM »
laser is k-40 co2 40w Orginally.... long long time go  :D

voltage you mean what I use control psu in the board ?
 post prosesor if i use m3 and m5 command work ok turn on and off like plasma cutter mode its work ok

but if make code for milling mahcine turn on and off command not work but data for z axle how I  convetter  spindle command that
or Do I must make post prosessor ? then z go negative turn on beam and z go exsample +00.01 turn off ?

and how work digital trigger what code that need

I am out of control :D

General Mach Discussion / laser setings
« on: November 15, 2012, 02:28:17 AM »
hi I want ask  how I can make settings for laser ?

Yes I can make lazy cam code for dxf mode  plasma and run and cut ok

But I want make z axle convert fire for laser beam like that then z go negative beam its start burn and if it go deep give more voltage and more power and z go 0.00 or positive beam end

Or how I get digital trigger work ?

my board tb6550 blue 4 axle

and I use relay for beam control   output 1 pin 2  work ok in lazy cam in plasma mode

do I get z axes data in pin and make transitor circuit swiths run beam ?
but I make vector cut artcam pcb  code and I run in mach work very good milling virtual  works ok

but not work start code and beam not response z control  beam start if I code run and end then code end but not lift up z axle control

Pages: 1