Hello Guest it is March 07, 2021, 03:18:43 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - TPS

801
General Mach Discussion / Re: Mill or Turn?
« on: May 14, 2019, 08:18:56 AM »
The home position is the "master tool" all tools are offset from there so it means you can replace any tool and reset the tool offsets for it and not have to worry about it messing with any other tool. As all tools are set to their respective diameters from the home position you do not usually need to alter the X value for your G54 (or other) offset. The Z G54 will need to be set for every different part you do but that is easy enough as you just call any tool you like, move it to the end of the stock and then zero the Z work offset. Doing that will mean every other tool will also now have their Z Zero work offset position as zero when they are touching the end of the material.



It works, I couldn't figure it out but once you try it, it makes sense, thanks Hood.

Next - my servo spindle drive seems odd.

At up to 2990 rpm in CS-Labs Pid tuning, it runs nicely with a low following error, about 1500 IIRC, at full speed of 3000 rpm I see a runaway following error - just carries on rising and would eventually trip an e-Pid fault on max following error i guess.

Its not serious, its only 10rpm lost but seems odd??

sounds like you have reached the 10V at 2990rpm.

802
General Mach Discussion / Re: Motors stalling /growling
« on: May 14, 2019, 01:35:04 AM »
in c:\Mach3 is a file  "yourprofilename".xml where all Settings are stored.

803
General Mach Discussion / Re: Motors stalling /growling
« on: May 13, 2019, 01:13:14 PM »
can you post your xml

804
General Mach Discussion / Re: Mill or Turn?
« on: May 11, 2019, 06:29:17 AM »
happy to hear that you have figured it out. :)

would be interested witch Setup you are planning for lathemill?

805
VB and the development of wizards / Re: Z axis zero
« on: May 11, 2019, 02:27:58 AM »
after you do you probe z-axis dro must Show +9.96mm,
otherwise your PlateThickness is not stored in UserDRO(1151)

btw where (Screen) do you set your PlateThickness?

806
General Mach Discussion / Re: Mill or Turn?
« on: May 10, 2019, 09:25:18 AM »
watched the Video several times, not sure what you mean.

it can be Encoder related, i think you are using Encoder Output from servo Controller?

how are Pn016 and Pn017 set?

807
General Mach Discussion / Re: Mill or Turn?
« on: May 10, 2019, 06:19:26 AM »
Quote
Any ideas?

not realy, maybe use another free analog Output?

can not test this here, the IP/S does not Support spindle axis with analog out only step/dir.

808
General Mach Discussion / Re: Parallel port issue
« on: May 10, 2019, 05:11:21 AM »
can you do a test like here:
https://www.youtube.com/watch?v=uglCm_qsojk

809
Mach3 under Vista / Re: Mach 3 with usb controler
« on: May 10, 2019, 03:48:11 AM »
found some Kind of instruction here:

https://de.aliexpress.com/item/MACH3-USB-interface-board-instruction-BL-UsbMach-V2-0/32821140872.html

if you scoll down you will find Input/Output settings

810
General Mach Discussion / Re: Parallel port issue
« on: May 10, 2019, 03:40:29 AM »
is the new Printer Card 3.3V or 5V Version?