Messages

661

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: August 12, 2019, 12:32:24 PM »

sorry i was wrong, there are no macro's for this Standard functions,
you only have to define the Outputs in Port's&Pins -> spindle Setup
and then in ports&pins -> Outputs your real CSMIO outputs

662

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: August 10, 2019, 03:17:11 AM »

in a Standard Installation they are for example in C:\Mach3\Macros\Mach3Mill

if they are not in your profilefolder, you can copy them from there.

663

General Mach Discussion / Re: Ethernet Smooth Stepper with THC

« on: August 05, 2019, 01:06:06 AM »

do you have the Torch On Signal wired and working?

664

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: August 03, 2019, 06:22:18 AM »

you should find

M7.M1s -> Mist coolant on
M8.M1s -> Flood coolant on
M9.M1s -> All coolant off

in c:\Mach3\macros\your Profilename


if not, you can just create them.

thay will work with GCode and MDI Input and as well with Standard screenset Buttons.

665

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: August 02, 2019, 05:16:14 AM »

so on witch way do you want to enable vacuum , GCode via M-funtion or external button.
same with dust shoe

666

CS-Lab / Re: CSMIO-ENC Spindle Orientation

« on: July 28, 2019, 07:14:54 AM »

well sounds like it is time to contact CS Lab.

667

CS-Lab / Re: CSMIO-ENC Spindle Orientation

« on: July 27, 2019, 10:55:59 AM »

and what angledifference does the M20 errormessage Show?

668

German / Re: Bauteil ausrichten

« on: July 27, 2019, 10:24:10 AM »

Hallo,
irgendwie habe ich den Post verpasst:

siwi ist der Winkel im Bogenmaß, da die Sin/Cos Funktionen einen Winkel im Bogenmaß erwarten
hywi ist der Versatz, der sich aus dem aktuellen Durchmessers des Werkzeugs ergibt, da der neue Nullpunkt ja im Zentrum der Spindel sein soll.

669

CS-Lab / Re: CSMIO-ENC Spindle Orientation

« on: July 27, 2019, 09:13:55 AM »

ok did a Little bit of reading about M20.

from the Manual (https://www.en.cs-lab.eu/technical-support/download/addons-macros/macro-m20-for-spindle-positioning/)

1.Settings:
a.Using M20 macro for spindle positioning, you can’t use „Align at stop” function at the same time (plugin „Spindle” tab) and reversely


3. The M20 macro verifies the set and real position after spindle positioning.
If the difference between those two values is higher than „Const Offset = 1” parameter value, the „M20 ERROR Offset !!!„ error will appear.
The „Const Offset” value can be reasonably adjusted to our needs (the value of 1 is usually optimal).


that means you can "Play" (increase) a bit with the

Const Offset = 1

in M20.M1S macro.


btw:
I can get orientation to work perfectly in the CSMIO plugin config page

how did you do this?

670

CS-Lab / Re: CSMIO-ENC Spindle Orientation

« on: July 27, 2019, 07:50:32 AM »

ok, that means the Motor Controller tunning is OK.

have you tryed to reduce the spindle acceleration/deceleration in CSMIO plugin Setup ?

6000rpm/s is pretty high.