Hello Guest it is March 19, 2024, 12:30:08 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - TPS

521
General Mach Discussion / Re: Mach3, Opt Laser 5W and Aspire
« on: February 25, 2021, 12:28:11 AM »
you have to choose TTL(H) variant.

522
General Mach Discussion / Re: Mach3, Opt Laser 5W and Aspire
« on: February 24, 2021, 02:15:57 PM »
you are right, sorry to Point you to the wrong circuit.

523
General Mach Discussion / Re: Mach3, Opt Laser 5W and Aspire
« on: February 24, 2021, 01:39:33 PM »
the plan is to use the PWM Input of your Laser control

524
General Mach Discussion / Re: Mach3, Opt Laser 5W and Aspire
« on: February 24, 2021, 01:37:10 PM »
I control the spindle speed through mach3?
yes, but you control it by using the 0-10V Signal, or am i wrong?

525
General Mach Discussion / Re: Mach3, Opt Laser 5W and Aspire
« on: February 24, 2021, 01:29:52 PM »
Do you mean yes but still have to build Tweakies board?

you have to build tweakies board, because your BOB creates 0-10V and no PWM as far i can see.

526
General Mach Discussion / Re: Mach3, Opt Laser 5W and Aspire
« on: February 24, 2021, 01:28:07 PM »
can pin 14 be used where my spindle is usually connected?
Yes.

but then you have to use two profiles or Change pin assignment in Config -> Port's and Pin's ->Motor Outputs ->
Spindle.

527
General Mach Discussion / Re: Mach3, Opt Laser 5W and Aspire
« on: February 24, 2021, 01:24:51 PM »
can pin 14 be used where my spindle is usually connected?
Yes.

528
General Mach Discussion / Re: Mach3, Opt Laser 5W and Aspire
« on: February 24, 2021, 01:09:55 PM »
btw. are you using the relay on your BOB?

Remind me where to check that?


Forget it, had a look to the layout of your BOB, the NC contact is not connected to a terminal.

a try would be to use a external relay on Pin8 and use this relay to Switch the 0-10V Signal, but im affraid
that the relay switching time will also create burns.

so last Option:
Tweakie has published here: http://www.tweakie.byethost10.com/27_files/Page1020.htm
a small circuit to use PWM and Output for fast switching.
your laser also accepts PWM and you can use Pin 8 and 9 for this.




529
General Mach Discussion / Re: Mach3, Opt Laser 5W and Aspire
« on: February 24, 2021, 01:00:48 PM »
btw. are you using the relay on your BOB?

530
General Mach Discussion / Re: Mach3, Opt Laser 5W and Aspire
« on: February 24, 2021, 12:58:10 PM »
This is what they said earlier
"Set the adapter back to program 0, then enable inputs are not used. inputs is mostly for advanced use.
This will solv the problem."
sorry i overread this, that's bad, because the only way in Mach3 is to use M10/M11 for fast switching laser,
M3/M5 in combination with S-word is to slow and you will allways get burn marks at start and end.