Messages

2271

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 16, 2015, 07:06:43 AM »

Hi Emil,

looks quite good so far.

--2-I don't know why on Y the cnc made mirror (it is perhaps because I revrse Y Axis on home limit set-up) ? I revrse the Y because by Manual-Jog.

X and Y have to be set like a normal coordinate system, so if we say in a rectangle
X0Y0 is the left bottom corner

X+ is going to the right side
Y+ is going upwards

allways relayed to the material.

for your spindle CCW turn.
have you tryed this pin 4   (REV)  reverse rotation -> csmio digtal output to switch CW/CCW
on the inverter for reverse run ?

Thomas

2272

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 08, 2015, 02:07:12 PM »

thank's a lot Thomas !
It's no problem with the manual language = "Ich spreche auch Deutsch - Zwei Jahre in Deutschland gelebt, im Koblenz"

ok das ist gut.

Thomas

2273

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 08, 2015, 02:05:57 PM »

@Hood

are still watching this, to be my second chance ?

Thomas

2274

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 08, 2015, 07:24:17 AM »

Hello Emil,


good news, got a manual from HSD, bad news (for you), it is in german.

but anyway, the table for connections on page 30 looks quite good,
so i made a small table for connections:

28   (REF-V) 0-10V analog input -> csmio analog output
29    (GND-A) for analog input

5   (in 5) enable inverter -> csmio digital output
4   (REV)  reverse rotation -> csmio digtal output to switch CW/CCW

8   (CM-IN) GND -> 24v GND

1   (FLT-NO) alarm relais -> csmio input inverter ready

2   (FLT-CM) for alarm relaise -> 24V+
6   (EXTFLT) external alarm -> 24V+
22   (IN3)    temperature motor (not used) ->24V+
17   (OUT3-CM) -> 24V+
16   (OUT3-NO) -> csmio input output frq. = 0 allow tool change



30   (CM-OUT) ?? -> csmio input frq. reached but it is a open collector
32   (OUT2)    ?? is connected to 24V+ does not make sence
    
so if only OUT2 is connected i should work with this 30/32 connection.

Thomas

2275

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 07, 2015, 08:57:25 AM »

Yes,

user for example SWX wire it to a input and
cofigure in Port's&Pin's the same inputs fpr X+ and X-.

there is only one switch, but there should be two braket's to trigger it.

Thomas

2276

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 07, 2015, 07:14:26 AM »

Hi Emil,

for the axis inputs, just seperate them from the e-Stop chain.

they should be NC contacts anyway, not like in the drawing as NO contacts.

Thomas

2277

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 07, 2015, 06:20:06 AM »

Hi Emil,

maybe you can test with pin4 (input witch is in standard config for
Reverse.

make one test pin4 connected to +24VDC and
one with pin 4 not connected.

let's try and error.

Thomas

2278

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 04, 2015, 12:35:49 PM »

Hello Emil,

here: http://www.gk-world.com/html/gongkongziliaowo/bpycd/bianpinqi/2013/1211/69372.html
i found a manual (scrolldown to get to wiring diagrams).
but some of the terminal numbers are different.

not realy shure what we can thrust ?

Thomas

2279

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 04, 2015, 06:29:28 AM »

Hello Emil,

i have got no answer from HSD.

the wiring diagram looks ok, the only signal
i am not clear is this frequency level signal.
may be the best thing is to fire up the spindle
and have a look what is going on with this signal.

Thomas

2280

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 01, 2015, 02:38:02 AM »

Hello Emil,

--I need help with:
--1-After Homing I have no ideea how can I reset the machine coordinates at 0 ?

are you using the 1024 screenset, if yes have a look in diagnostic page, there you can see
all coordinates. normaly the machine coordinates are set to 0 by reference, what you see
in the main screen are the work offsets, witch may be different.

--2-Got problem on wiring and declare inputs/outputs on  the (VFD-spindle ) , found no where  (Mach3-csmio) somethingh about frequency level and frequency reached
--(attach inverter electr schema) ?

i have written HSD an email about manual.
i think for the beginning it is enought to wire
-csmio analog output to analog input of vfd
-csmio digital output for enable vfd
-inverter ok to a csmio input
-and if you want the frequenzy reached to a csmio input

at least the 24V and GND.

Thomas