Messages

2261

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 17, 2015, 04:35:46 PM »

Hi Emil;

Thomas

I use already 2 relays to change the direction but some people said is not OK to use by M4 - to +; but if you say is OK then I will do it.

maybe i missed something about this two relaiys,
pls give me a short update about this two relais.

Thomas

2262

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 17, 2015, 11:23:33 AM »

Hi Emil,

When I change the reff wires the spindle change direction.
Can you help me with the tool change VB ?

that means you can use a gold contact relay to swap the wires to change direction.
wire this relay to a csmio output and we do some changes in M3/M4 to get this
working.

just let me know what help you need for the toolchange macro.

Thomas

2263

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 17, 2015, 09:27:26 AM »

by the way,

is the spindle changing direction if you swap the analog Input wires ?

2264

CS-Lab / Re: Retrofit CNC Bulleri FPM 2813-Osai controll with CSMIO-IP-A

« on: June 17, 2015, 09:23:03 AM »

Hi Emil,

is there any posibility on this Inverter to Change Parameters,
in the Manual it does not look like there is any Display.

my email is below  the avantar.

Thomas

2265

General Mach Discussion / Re: feedrate changing after spindle stop part 2

« on: June 17, 2015, 05:02:28 AM »

Hi Fred,

i have tested on Version R3.043.058.
i am living in Bavaria near Regensburg.

yes please post your xml i will have a look.

Thomas

2266

Brains Development / Re: compare immediate not working

« on: June 17, 2015, 04:57:40 AM »

Hi George,

tryed to find the code of your truth table.
it is not binary and not gray code.

anyway i would start with a simple brain, only 2 or 3 numbers,
and also not use the compare instruction.

attached a small sample i would start with.

Thomas

2267

General Mach Discussion / Re: feedrate changing after spindle stop part 2

« on: June 17, 2015, 03:52:14 AM »

Hi,

tested your file.
i have a constant feedrate from 0.1
during the complete run.

Thomas

2268

General Mach Discussion / Re: feedrate changing after spindle stop part 2

« on: June 16, 2015, 05:10:59 PM »

Hi Fred,

thanks for that thomas- i did change the line and still have the same problem.

If i were to send you my file would you be able to put it on your computer and
see if it runs correctly.

I did recently pick up a compile error regarding one of my M files and i am concerned
that i may have got some form of corruption

I would appreciate your help

regards

fred

send me your files,  i'l have a look.

Thomas

2269

General Mach Discussion / Re: feedrate changing after spindle stop part 2

« on: June 16, 2015, 09:47:14 AM »

Hi,

g0z1         (move z closer)             ********this is where it always changes the feedrate


it is a G0 i think it should be G1.

Thomas

2270

Brains Development / Re: compare immediate not working

« on: June 16, 2015, 09:41:51 AM »

Hi,

please have a look for your truth table

Tool Position 1+8 have the same pattern
Tool Position 5+6 as well.

Thomas