Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - TPS

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 »

1641

General Mach Discussion / Re: VB Script

« on: October 09, 2018, 05:21:32 PM »

ok was a "Little bit" ofline, added some debuging msg boxes, to see what is going on

Code: [Select]

'simple X-center script
Sub Main()
	SetOEMDro(800,0)

    'do the X- probe 
    Message ("probe X- ")
    Code "G31 X-100 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x <= -100 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X- canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeXNeg = GetVar(2000)

	
	MsgBox "X Probe - : " + CStr(ProbeXNeg)
	
	
	'clear the probe
	Code "G91 X2 F150"
    While IsMoving() 
		Sleep(10)
    Wend           
	Code "G90"
	
	
    'do the X+ probe 
    Message ("probe X+ ")
    Code "G31 X200 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x >= 200 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X+ canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeXPos = GetVar(2000)

	
	MsgBox "X Probe + : " + CStr(ProbeXPos)
	
	

	'clear the probe
	Code "G91 X-2 F150"
    While IsMoving() 
		Sleep(10)
    Wend           
	Code "G90"
	
	'goto the center
	middle = ProbeXNeg + ((ProbeXPos - ProbeXNeg)/2) 


	MsgBox "center : " + CStr(middle)

	Code "G90 G01 X" + CStr(middle)
    While IsMoving() 
		Sleep(10)
    Wend           
	SetOEMDro(800,0)
	
End Sub

1642

General Mach Discussion / Re: VB Script

« on: October 08, 2018, 01:00:03 AM »

Code: [Select]

'simple X-center script
Sub Main()
	SetOEMDro(800,0)

    'do the X- probe 
    Message ("probe X- ")
    Code "G31 X-100 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x <= -100 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X- canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeXNeg = GetVar(2000)

	'clear the probe
	Code "G91 X2 F150"
    While IsMoving() 
		Sleep(10)
    Wend           
	Code "G90"
	
	
    'do the X+ probe 
    Message ("probe X+ ")
    Code "G31 X200 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x >= 200 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X+ canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeXPos = GetVar(2000)

	'clear the probe
	Code "G91 X-2 F150"
    While IsMoving() 
		Sleep(10)
    Wend           
	Code "G90"
	
	'goto the center
	middle = ProbeXNeg + ((ProbeXPos - ProbeXNeg)/2) 
	Code "G90 G01 Y" + CStr(middle)
    While IsMoving() 
		Sleep(10)
    Wend           
	SetOEMDro(800,0)
	
End Sub

1643

General Mach Discussion / Re: VB Script

« on: October 07, 2018, 01:47:10 PM »

no idea why this warning Comes up, but try this code:

Code: [Select]

'simple X-center script
Sub Main()
	SetOEMDro(800,0)

    'do the X- probe 
    Message ("probe X- ")
    Code "G31 X-100 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x <= -100 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X- canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeXNeg = GetVar(2000)

	'clear the probe
	Code "G91 X2 F150"
    While IsMoving() 
		Sleep(10)
    Wend           
	Code "G90"
	
	
    'do the X+ probe 
    Message ("probe X+ ")
    Code "G31 X200 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x >= 200 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X+ canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeXPos = GetVar(2000)

	'clear the probe
	Code "G91 X-2 F150"
    While IsMoving() 
		Sleep(10)
    Wend           
	Code "G90"
	
	'goto the center
	middle = ProbeXNeg + ((ProbeXPos - ProbeXNeg)/2) 
	Code "G90 G01 Y" + CStr(middle)
	SetOEMDro(800,0)
	
End Sub

1644

General Mach Discussion / Re: VB Script

« on: October 07, 2018, 10:28:32 AM »

ok try this, sorry i can't test the code for the Moment.

Code: [Select]

'simple X-center script
Sub Main()
	SetOEMDro(800,0)

    'do the X- probe 
    Message ("probe X- ")
    Code "G31 X-100 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x <= -100 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X- canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeXNeg = GetVar(2000)

	'clear the probe
	Code "G91 X2 F150"
    While IsMoving() 
		Sleep(10)
    Wend           
	Code "G90"
	
	
    'do the X+ probe 
    Message ("probe X+ ")
    Code "G31 X200 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x >= 200 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X+ canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeXPos = GetVar(2000)
	
	'goto the center
	middle = ProbeXNeg + ((ProbeXPos - ProbeXNeg)/2) 
	Code "G90 G01 Y" + CStr(middle)
	SetOEMDro(800,0)
	
End Sub

1645

General Mach Discussion / Re: VB Script

« on: October 07, 2018, 08:18:56 AM »

Code: [Select]


'simple X-center script
Sub Main()
	SetOEMDro(800,0)

    'do the X- probe 
    Message ("probe X- ")
    Code "G31 X-100 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x <= -100 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X- canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeXNeg = GetVar(2000)
	
    'do the X+ probe 
    Message ("probe X+ ")
    Code "G31 X200 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x >= 200 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X+ canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeXPos = GetVar(2000)
	
	'goto the center
	middle = ProbeXNeg + ((ProbeXPos - ProbeXNeg)/2) 
	Code "G90 G01 Y" + CStr(middle)
	SetOEMDro(800,0)
	
End Sub

1646

General Mach Discussion / Re: VB Script

« on: October 04, 2018, 03:04:36 AM »

here a simple sxript for X

Code: [Select]

'simple X-center script
Sub Main()
	SetOEMDro(800,0)

    'do the X- probe 
    Message ("probe X- ")
    Code "G31 X-100 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x <= -100 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X- canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeX- = GetVar(2000)
	
    'do the X+ probe 
    Message ("probe X+ ")
    Code "G31 X200 F150" 
    While IsMoving() 
        x = GetOEMDRO(800) 'X actpos
        If x >= 200 Then
            DoOEMButton(1003) 'Stop too far no probe hit
            MsgBox ("Probe X+ canceled , no probe hit!" )
            Exit Sub
        End If
    Wend           

	'get the exact probepos
	ProbeX+ = GetVar(2000)
	
	'goto the center
	middle = ProbeX- + ((ProbeX+ - ProbeX-)/2) 
	Code "G90 G01 Y" + CStr(middle)
	SetOEMDro(800,0)
	
End Sub

be careful, not tested, just written down.

z-axis has to be in probe hight.

1647

General Mach Discussion / Re: DRO question

« on: October 01, 2018, 01:41:56 PM »

i think you have to read a Little bit about machine coordinates and work coordinates.

machine coordinates will only be set to Zero by doing a reference with reference Switches.

1648

CS-Lab / Re: Completely lost with my CSMIO IP-m 4

« on: September 29, 2018, 03:27:00 AM »

if you use the CS-Lab email

office@cs-lab.eu

and ask for

Wojtek Trawicki

you normaly get a good Support.
i got allways an answer within two days.

1649

CS-Lab / Re: IP/M - Mach3 - Win10 - DRO Values unreasonable wrong ! (too high)

« on: September 29, 2018, 03:21:37 AM »

can you post your G-Code ?

1650

General Mach Discussion / Re: Mach3 motor tuning, homing and limits and machine units - Help please.

« on: September 28, 2018, 02:08:38 AM »

if you go to the settins page , right lower Corner, does it Show mm's or Inch ?