Messages

1391

General Mach Discussion / Re: MACH 3

« on: February 17, 2019, 03:14:01 AM »

according to your Diagramm X and Y are swapped.


     Y+
X- -|- X+
     Y-

thats how your tool should move on the surface.

1392

General Mach Discussion / Re: Pierce delay for plasma cutters.

« on: February 16, 2019, 05:40:26 AM »

have a look for:

Config -> General Config -> General Configuration -> G04 Dwell in ms

1393

Mach4 General Discussion / Re: hybrid servo motor, Pockeys57cnc and mach4

« on: February 15, 2019, 07:41:06 AM »

Hello Jonathan,

i will answere here, because other thread is not the right place i think.
i am afraid not to be a great help, because i have no experince in Mach4.
have you worked through all step's of the Manual witch start on page 30?

maybe one of the Mach4 guru's can jump in here.

Tom

1394

Mach4 General Discussion / Re: New people welcome !! Come in here and introduce your self!

« on: February 15, 2019, 06:35:35 AM »

i asume you have got this Manual:

https://www.poscope.com/wp-content/uploads/downloads/Pokeys/LibrariesAndPlugins/Mach4%20and%20PoKeys57CNC%20-%20step%20by%20step%20guide.pdf

it is very detailed how to get started.

1395

General Mach Discussion / Re: mach3 and Bridgeport Boss5

« on: February 14, 2019, 03:04:47 PM »

backslash?

1396

General Mach Discussion / Re: DQ542MA

« on: February 13, 2019, 04:41:48 AM »

why should it be something with the ACOI Drivers,
when your y-axis Controller is running on the x-axis Outputs of the BOB,
and only the new x-axis Driver is not working ?

1397

General Mach Discussion / Re: DQ542MA

« on: February 13, 2019, 01:45:27 AM »

sorry for the delay,
maybe you can post a photo of the Motor Connections at the DQ542MA and at the HY-Div 268N ?

1398

German / Re: Eine Tastplatte nutzen in Mach3 wie bei Estlcam ?

« on: February 11, 2019, 02:20:54 PM »

die Lösung ist der Code unten mit 4 Punkten, da dann der Fehler (durch die tangentiale Tastung) egal ist,
da ja sowohl in x und in y mit dem Fehler gearbeitet wir, dieser Code(unten) ist nur ein auf meine Maschine
angepasster code von dem anderen Thread.

1399

General Mach Discussion / Re: DQ542MA

« on: February 11, 2019, 01:46:07 PM »

and the Motor current?

1400

General Mach Discussion / Re: DQ542MA

« on: February 11, 2019, 01:20:38 PM »

if i have a look to the Manual:

1Off
2On
3On

means 0,6A Motorcurrent

4Off
5On
6Off

means 1/8 step ,if you have a stepper Motor with 400 imp/rev -> 3200 imp/rev

according to this https://wiki.kreitek.org/_media/proyectos:cnc:div268n-5a-datasheet.pdf manual



your posted DQ542MA setttings where:

1 Off
2 On
3 Off

means Motor current 3,31A

5 Off
6 Off
7 On
8 On

means 1600 pulses/rev

according to this: https://www.hobbytronics.co.za/Content/external/472/DQ542MA%20English%20Manual.pdf  Manual



so something does not match