Messages

1221

General Mach Discussion / Re: My stepcraft DL445 laser leaves a path

« on: June 13, 2019, 12:51:35 PM »

sorry missed that you posted your Profile.

you are Controlling your laser via Spindle Motor control step Signal (chankspindle/chankspindleoutput).

output1 is assigned to pin0 (chankoutputs), so M10P1/M11P1 can not work (should be pin17)

1222

General Mach Discussion / Re: My stepcraft DL445 laser leaves a path

« on: June 13, 2019, 12:36:52 PM »

never used it, but M10P1 means Switch Output 1 ON, and to what (ports&pins) is your Output#1 assigned.

for the Moment you use M3/M5 to turn laser ON/OFF?

what is your output configuration Config -> Ports&Pins -> Spindle Setup -> Relay Control ?

are you using are original UC100 or a chinese clone?

1223

General Mach Discussion / Re: too slow for pulley using min

« on: June 13, 2019, 12:21:21 PM »

for radius Problem goto Config -> General Config and make Setting correspondig to post processor

1224

General Mach Discussion / Re: too slow for pulley using min

« on: June 13, 2019, 12:18:39 PM »

goto Settings and check witch pulley is selected

goto Config -> Spindle Pulleys and check Min value of selected pulley

1225

General Mach Discussion / Re: My stepcraft DL445 laser leaves a path

« on: June 13, 2019, 12:12:34 PM »

had a quick look to the UC100 manual Appendix A. : New functions and bug fixes:
it should Support M10/M11.

but don't know wether it is working

1226

General Mach Discussion / Re: Motors stalling /growling

« on: June 10, 2019, 03:42:42 AM »

ok that means microstepping and steps per are correct.
next step would be to have a look with oszilloscope for the step/dir signals.

1227

General Mach Discussion / Re: Motors stalling /growling

« on: June 09, 2019, 06:35:41 AM »

When entering the G1 xo.1968 f1, it keeps turning never stops and is very slow and rough sounding.

have you zeroed x-axis before Input?

1228

General Mach Discussion / Re: Motors stalling /growling

« on: June 08, 2019, 03:23:49 AM »

hi,
one idea is left. can you pls do a

G1 X0.1968 F1

in MDI, and confirm that the Motor does exactly one Revolution?

1229

General Mach Discussion / Re: Motors stalling /growling

« on: June 05, 2019, 01:22:07 AM »

can you post a Video with Sound?

1230

General Mach Discussion / Re: Motors stalling /growling

« on: June 04, 2019, 02:25:07 PM »

ok lets start again, i only want to double check everything.

Motor 34HS5435C-37B2:

red    -> DM860A   A
green  -> DM860A   A-
yellow -> DM860A   B
blue   -> DM860A   B-




DM860A:

dip switches current
SW1 -> OFF
SW2 -> OFF
SW3 -> ON

dip switches micro stepping
SW5 -> ON
SW6 -> OFF
SW7 -> ON
SW8 -> ON

wiring signals
PLS+ -> DB25-1205 pin 2
DIR+ -> DB25-1205 pin 3
PLS- -> DB25-1205 pin GND
DIR- -> DB25-1205 pin GND
(only for the x-axis)

V+  -> Power Supply +
GND -> Power Supply GND



BOB DB25-1205 minimal wiring for x-axis

pin 2 -> DM860A PLS+
pin 3 -> DM860A DIR+ 
pin GND -> DM860A PLS-
pin GND -> DM860A DIR-

pin VDD -> external power supply 5V
pin GND -> external power supply GND

JN1 connected
JN2 connected

JN4 here i am not realy sure what the manual is trying to tell me



ethernet smoothstepper minimal wiring

25pole ribbon cable to db25 connector for BOB
ethernet cable to pc
external power supply for 5V connected


motor tuning settings (we discused a lot)
steps/per 8128
vel 60
acc 12






hope i got the mayor things, pls take the the time to go through this list step by step and doublecheck,
i have taken the time to create it.