Messages

11

Works in progress / Re: 1st 'Beta' release of the MachSteelBlue Screenset

« on: June 17, 2007, 06:14:59 PM »

Hi Sterling,

Will investigate and see what can be done. If I remember correctly our screens were for v1.84 releases and now with the 2.00 releases some features are not correct. i.e No sliders.

Would love to get the time again to do another set of screens. But time just isn't good at the moment

Cheers

12

Works in progress / Re: My Simple Screen for Touch

« on: June 17, 2007, 06:08:57 PM »

Really got to echo what Zealous said. Love the vibrant colours.

Great Work !

13

Works in progress / Re: 1st 'Beta' release of the MachSteelBlue Screenset

« on: June 12, 2007, 04:51:49 PM »

Hi Sterling,

Certainly not reading on anyone's toes. Any feedback good or bad is more than welcome.

The one thing I'm not quite sure on is the problem you have specific to the SteelBlue Screen or does it also exist in the standard Mach screens ?

The SteelBlue screens should (We hope) only use the exact commands as the original Mach screens. They were put together at 2am most nights so not the best of times to work 

If it's the same problem with both screens then it's a job for a Guru, if not drop a note and we'll investigate.

Cheers

14

Works in progress / Re: New screen for Ascension 1000 users

« on: February 08, 2007, 05:44:53 PM »

Truly outstanding.

Really professional.

Well done !

15

Works in progress / Re: An unfinished screen set - "Mach Blue"

« on: November 06, 2006, 11:53:26 AM »

Great service again.

Thanks Art.

16

Works in progress / Re: An unfinished screen set - "Mach Blue"

« on: November 03, 2006, 04:35:37 AM »

I did get a notify this time.

Thanks for the confirmation Chad. Not good news for Nikl but at least we know the problem exists.....

I'm not sure if there is anything we can do with the screenset to fix it ? 

17

Works in progress / Re: An unfinished screen set - "Mach Blue"

« on: November 03, 2006, 04:12:29 AM »

Nikl,

Apologies for the delay. Again my spam filter hid the automail from the board to alert me of your post.

Unfortunately, I am unable to veryify your problem as the Conversational  is an extra that needs to be purchased. (I think!)

I really need the help of someone else to check this problem.

I'm not sure if our screens would cause an error as they are basically just a front end calling up certain codes when buttons are clicked. Saying that I don't know Mach well enough to use it in anger.

Good luck, I hope you get an answer, sorry cannot be of more use.

18

General Mach Discussion / Re: PCB milling

« on: September 07, 2006, 08:47:57 AM »

For some interesting work on PCB milling take a look at some of Mr Beans work.

Quite amazing pcb milling screenshots.

http://www.cnczone.com/forums/showthread.php?t=23363

Regards,

19

Works in progress / Re: An unfinished screen set - "Mach Blue"

« on: September 01, 2006, 04:19:33 AM »

Krymis,

Apologies for the delay replying. For some weird reason, my internet provider (BT) is putting all of the notifications from this site into it's spam filter

I have to manually check the filter to see the posts on here.

Regarding the screenset this shouldn't cause any problems with the emergency stop feature.

By default what you describe occurs in Mach unless you go in and configure the port / pins etc.

Have you done this ?

Cheers

20

Works in progress / Re: Mach3Turn - 1st 'Beta' release of the SilverBlue Screenset for lathes

« on: July 14, 2006, 02:47:19 AM »

Art,

Many thanks. It's a cool piece of code.

(Some heavy maths in there !)

Regards