Messages

11

PoKeys / Re: 2 Pokeys 56U boards

« on: July 15, 2012, 05:19:14 PM »

NeoTO,
Thanks again for the info, I have it working now.

Regards,
Raul

12

PoKeys / Re: Pokeys and mach 3 not working

« on: July 15, 2012, 05:17:01 PM »

Hi Mikael,
First I would save your xml files so you won't loose any of your Mach3 settings. Then I would un-install Mach3 and Pokeys plugin. Re-install Mach3 version R3.043.062 and the latest Pokeys plugins and software and you should be fine.
Regards,
Raul

13

PoKeys / Re: 2 Pokeys 56U boards

« on: July 10, 2012, 04:05:42 PM »

NeoTO
Thank you, I will try it out.
Regards
Raul

14

PoKeys / Re: 2 Pokeys 56U boards

« on: July 10, 2012, 11:23:45 AM »

I have the latest plugin. Both boards work, what I'm trying to do is connect an MPG rotary dial to the second pokeys board, but I am not having any success on getting it to work. I have found documentation setup for the old pokeys plugins but not for the latest one. So I'm a little list on how to set this up.

Regards
Raul

15

PoKeys / 2 Pokeys 56U boards

« on: July 10, 2012, 06:31:52 AM »

Hi all,
I need a little help! I have 2 Pokeys 56U boards connected to Mach3. If you have one Pokeys 56U board connected to Mach3 and the input port is port 10. What would be the input port for the second Pokeys 56U Board?

Thanks,
Raul

16

PoKeys / Re: Pokeys and mach 3 not working

« on: July 10, 2012, 06:25:38 AM »

NeoTO

Thank you, I did exactly what you said, and it works just fine. I uninstalled and re-installed all software and plugins and it works great.

Thanks again,
Raul

17

PoKeys / Pokeys and mach 3 not working

« on: June 26, 2012, 05:53:13 PM »

Hi,
I recently installed a smooth stepper board for mach3. I had removed the pokeys 56u board from my setup until the new plugins arrived. Now I installed the new plugin and software pokeys. As i try to configure pokeys board thru mach 3 I am unable to get it to work. When I access the configuration screen thru mach 3 I am able to make changes but I nothing will happen with mach 3. I need some assistance. Can this be an issue with using both the smooth stepper and pokeys?

Thank you,
Raul

18

General Mach Discussion / Re: Control spindle speed with potentiometer and pokeys board

« on: April 05, 2012, 02:13:57 PM »

Thank you once again.

Raul

19

General Mach Discussion / Re: Control spindle speed with potentiometer and pokeys board

« on: April 05, 2012, 01:59:06 PM »

Hood,
Thank you for your response. I am trying to find your post. Any chance you can give me the link to your post on the FRO and SRO.

Thanks again,
Raul

20

General Mach Discussion / Control spindle speed with potentiometer and pokeys board

« on: April 05, 2012, 01:07:47 PM »

Hi all
I need some help!
I have a pokeys 56U board and I have a potentiometer connected to it. I want to able to control my spindle speed with it. How would I go about doing this. Would I need to use brains? If so what formula would I need?

I also want to be able to change the feed rate with a different potentiometer.

Raul