Messages

41

General Mach Discussion / Re: Version 061 Backlash Comp Problem

« on: March 28, 2007, 09:05:16 AM »

I have and had the same problem from version 51, and I do not know how to setup the values for shuttle acceleration. What is the rule, please?

Thank you.

Zoltan

42

General Mach Discussion / Re: version 59 and 60

« on: March 27, 2007, 05:22:55 PM »

Not yet. Sorry.

Zoltan

43

General Mach Discussion / Re: version 59 and 60

« on: March 27, 2007, 04:46:06 PM »

And, sorry for not asking in previous post, could someone tell me where I can find out information about shutle wheel acceleration/decelaration setting?

Thank you,

Zolt

44

General Mach Discussion / Re: version 59 and 60

« on: March 27, 2007, 04:43:58 PM »

I have run w/o backlash, and the same issue, but only if the program is bigger than 500K. Any explanation/help?

Thank you.

Zoltan

45

General Mach Discussion / Re: version 59 and 60

« on: March 26, 2007, 03:35:01 PM »

Yes, I forgot. I have a license for Mach3 and one for Lazycam Pro. They are on my wife's name as the payment was done from her card..she knew and knows.

Zoltan

46

General Mach Discussion / Re: version 59 and 60

« on: March 26, 2007, 03:30:16 PM »

Hi,

I did not make any driver test, yet, but until now I had no problems. I am running Quantum on the same computer, nothing else, and it works extremely well. The computer is Dell 1.7Ghz with 512M memory and 20G hard. The machine has 6.8Nm stepper motors on all axis with ballscrews. The drivers are Geko. Yes, if the backslah is not active the machine is not oscillating, but I did not run the files w/o backlash to see if the skipping happens again. When I run first time I have run on  sheet of Komacel and I have ruined it. It is very expensive here, at least for me. Afterwards I have run different files on some foam pieces with backlash.

Zoltan

47

General Mach Discussion / Re: version 59 and 60

« on: March 26, 2007, 01:06:47 PM »

Hi,

Actually, I do not know how to do the setting. If I make the backlash active and I am not changing the value of shutle wheel acceleration the machine is oscillating when it reverses. I have changed arbitraly the value until the oscilating starting-slowing down-accelerating-speed..etc disapered, or I just set up a value of 0.0001. I do not know anything about this setting, and found out nothing also. I read on the version history a short note about changing this setting. The note was, if I remember corectly on version 51.

Zoltan

48

General Mach Discussion / version 59 and 60

« on: March 26, 2007, 11:02:03 AM »

Hi,

I gave few trials of 59 and 60 versions. I had the same issue with both of them. If the file is bigger that 500K in the midlle of running the machine is skipping steps. It does not matter with what program I have generated the path. I have tried Vcarve and Sheetcam. I do not understand why. Also, for me is not clear the Shutle Wheel Settings and how this is connected with backlash. Could someone help me, please?

Zoltan

49

General Mach Discussion / Re: Tool measure macro

« on: March 04, 2007, 06:19:09 AM »

Fabiano,

Did you succeed to make macro working OK? I mean accuracy? If yes, could you, please, pot it here. I would like to try it.

Thank you,

Zoltan

50

General Mach Discussion / version 2.00.049 strange behaviour

« on: February 26, 2007, 05:24:01 PM »

Hi,

Today I have updated to version 49. Btw it asked me during updating if I would like to update to version 48 which has been already installed. The strange thing is that during run the sprogram skipped couple lines of program. I installed the version 49 on other computer (also 1.7 GHz) and I got the same behaviour but with another file. I have re-installed version 48 and everything seems ok. Could someone help?

Thank you,

Zoltan