Messages

991

Show"N"Tell ( What you have made with your CNC machine.) / Re: I'm in Hog Heaven

« on: January 09, 2015, 05:11:56 PM »

good work

992

Mach4 General Discussion / Re: What type of performance improvements could expected by using Mach 4

« on: January 08, 2015, 03:15:55 PM »

running M4 on the pp is a lot better than M3 on pp I found it to be a large difference in performances and speed and things like soft limits are just better

993

Newfangled Solutions Mach3 Wizards / Re: PHOTOvCARVE problems!!

« on: January 02, 2015, 10:04:49 PM »

that's a good idea your problem is strange

watch the youtube videos by hoss its where I learnt most of the M3 stuff I know

https://www.youtube.com/channel/UCjoRKEpk7uE5Wzf4b-IFTFg

994

Newfangled Solutions Mach3 Wizards / Re: PHOTOvCARVE problems!!

« on: January 02, 2015, 06:38:00 PM »

see if you can find someone near you to come help.

if you are using the default G540 config all you need to change is the stepper values and it should work. do you have safe Z set to 0.25

995

Newfangled Solutions Mach3 Wizards / Re: PHOTOvCARVE problems!!

« on: January 02, 2015, 04:22:46 PM »

that sucks that it still wont play nice does its still work ok doing cuts in cut 2D

996

Mach4 General Discussion / Re: Screen Set Ideas

« on: December 31, 2014, 12:11:34 AM »

lua is not all that hard to do it just when you have to have bits in other places that makes it hard I have done a couple of codes they worked in the Editor but don't work in the screen because of the other bits need in other places.

most of what you will wont to be in screen sets will be there soon there is only 1 more thing I wont to add and that's a laser zero for x and y

there are other people working on screen sets that will be as good as what Craig is doing for his self

997

Mach4 General Discussion / Re: Screen Set Ideas

« on: December 30, 2014, 02:51:17 AM »

yes its hard to do if anyone did the time Craig put into learning lua you would be at the same place he is what he does does help so what if he does not wont to give over what he has learnt that up to him yes it`s our loss if he wont to realise a screen set down the line cool I would pay for it to.

also BR549 you have not given over what you have worked out to do I asked you all ready you did not reply.

I have stop playing with M4 when the manual comes out I will start again.

Linux CNC fell over because you almost need to be a programmer to use it I tried said f that when back to m3

998

Mach4 General Discussion / Re: Screen Set Ideas

« on: December 28, 2014, 10:11:33 PM »

good work Ya-Nvr_No do what ever you wont it all help

999

General Mach Discussion / new computer for M3 and Later M4

« on: December 28, 2014, 05:58:10 PM »

need some advices or help I have just changed computers on my machine old computer was a problem replacement computer works good as gold but its very old (cant run M4 very well)

was thinking of get a new pc or laptop the machine has a ESS so only need Ethernet.

what pc or laptop are people using that runs win 7 or 8 that don't have problems with said computer (brand, make, model)

1000

Mach4 General Discussion / Re: Mach4 Printer Port Discussions

« on: December 28, 2014, 01:29:55 AM »

you may just need to get the Darwin.m4pw and Darwin.sig and put them in the folder restart computer then run driver test restart computer and all should be good