Messages

321

General Mach Discussion / Re: Concrete printer anyone?

« on: February 25, 2016, 01:47:08 AM »

stacy take some picks of the inside of ya control box

322

Mach4 General Discussion / Re: Mach4 with ESS and PMDX126/107 speed control issues.

« on: February 24, 2016, 06:13:39 PM »

one other thing you have motor 0 set as 0 good.

then you have motor 1 set in motors tab then in Axis mapping you have motor 2 set as motor 1.

you should have motor 2 set as motor 2 in motors and Axis mapping

323

Mach4 General Discussion / Re: Mach4 with ESS and PMDX126/107 speed control issues.

« on: February 23, 2016, 07:20:22 PM »

yep ok have you set speed's in the Spindle page

so the on/off is working when you do a M3 is there voltage on pin 14, pin 16 is working.

pin 14 should just be high to low or low to high

324

Mach4 General Discussion / Re: Mach4 with ESS and PMDX126/107 speed control issues.

« on: February 23, 2016, 06:01:14 PM »

try without OB1 Daz said to not use it he is a IT guy who is not full off his self and is very good at this Mach4 stuff

325

Modbus / Re: Arduino Modbus, Complete, Documented and free

« on: February 23, 2016, 05:58:19 PM »

well a 10 meter USB cable is well not good change over to a Ethernet board

326

Mach4 General Discussion / Re: Mach4 with ESS and PMDX126/107 speed control issues.

« on: February 23, 2016, 05:41:06 AM »

good stuff it will be something small stopping it working

327

Mach4 General Discussion / Re: Mach4 with ESS and PMDX126/107 speed control issues.

« on: February 23, 2016, 02:37:19 AM »

joe45 do what daz says to do and you need to find how to go cw, ccw for threading and that sort of thing, so you can run a encoder on your spindle.

328

Mach4 General Discussion / Re: Mach4 with ESS and PMDX126/107 speed control issues.

« on: February 22, 2016, 04:20:59 PM »

do a reinstall as admin of M4 it should show more than 3 motors it does on my machine with a ESS

329

Mach4 General Discussion / Re: Mach4 with ESS and PMDX126/107 speed control issues.

« on: February 22, 2016, 04:43:49 AM »

vid  http://autode.sk/1SMma69

330

Mach4 General Discussion / Re: Mach4 with ESS and PMDX126/107 speed control issues.

« on: February 22, 2016, 04:32:58 AM »

how you had it in ESS config looks good in Mach set the spindle on (pin 14) to spindle forward in M4 ( so when you start the spindle it runs cw).

Set the spindle PWM (pin 16) to spindle on in M4 (so when you turn it on it runs at set PWM).

it's sound arise about faces but it works that way. if it does not work set that way flip it around also close and restart M4 when you change pin setting's

I would check if you realy need the charge pump that's a old school thing a properly set up E stop should be all you need. (it will be argued about)

I am not 100% sure but if I am wrong Ger or tweckey will jump in and say I am, admin.

just doing the vid now I have a speech problem so it just pointing, in outputs I type in a pin number it just where that pin is mapped to from the ESS config