Hello Guest it is March 29, 2024, 11:41:03 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - dude1

1021
Newfangled Solutions Mach3 Wizards / Re: PHOTOvCARVE problems!!
« on: December 20, 2014, 01:41:29 AM »
here`s the two file try on your original xml try the vcarve file first if its good try the photo vcarve they both are in inch they should run fine.

if the photo vcarve file works try one of your own that will test your version verses mine if your one fails report this to vectric if both fail going back to your orginal xml but the vcarve file works and one from cut2d works.
it could well be your computer if you can get another one with pp to try do it, its the only way to know if it is the computer.

I will run it on my machine tomorrow only need to change a couple of settings 

1022
Newfangled Solutions Mach3 Wizards / Re: PHOTOvCARVE problems!!
« on: December 20, 2014, 01:18:09 AM »
I cant send you a cut2d file don't have it any more I will send a vcarve pro file it might work

1023
Newfangled Solutions Mach3 Wizards / Re: PHOTOvCARVE problems!!
« on: December 20, 2014, 12:53:14 AM »
in morning go back to your original xml if cut 2d works properly on your old xml something is really wrong somewhere ever your machines computer or somewhere else I will post you a cut2d file and a photovcarve done in inch from here if the cut2d file is fine of what I send you try the photo Vcarve file if its still bad then its not cut2d or photo vcarve where the problem is

1024
Mach4 General Discussion / Re: Mach4 Printer Port Discussions
« on: December 20, 2014, 12:22:49 AM »
you funny art so far I seem to have only wasted your time and my own

1025
Mach4 General Discussion / Re: Mach4 Printer Port Discussions
« on: December 20, 2014, 12:04:26 AM »
yer I have done it all ready so been down the same road I set it by arts vids and the manuals the only problem I had was with the spindle it was a 3 axis as well.

now I am doing arts laser controller 

1026
Newfangled Solutions Mach3 Wizards / Re: PHOTOvCARVE problems!!
« on: December 20, 2014, 12:00:17 AM »
delete the xml I first sent try this one I have it locked to inch 

now try doing an air cut of something that has worked before not a photovcarve if its ok after checking that it is in inch mode it should not change and if the file runs fine try a photovcarve just do an air cut if it does not work as it should.

it has to be something with the computer as there is nothing strange happening with me just doing sims of your files on the xml you sent and the one I sent you.

you can use an computer to check setting with mach3 it does not need a pp for just testing I am using a laptop to do testing of files before I put them on the machines computer with the same xml

1027
Newfangled Solutions Mach3 Wizards / Re: PHOTOvCARVE problems!!
« on: December 19, 2014, 11:36:32 PM »
thats cool I have a 2 year old that jumps out windows

1028
Newfangled Solutions Mach3 Wizards / Re: PHOTOvCARVE problems!!
« on: December 19, 2014, 10:24:41 PM »
right here a test one for you try this just load it up then restart M3 turn the charge pump off switch on g540 as well.

load your photo vcarve file  set your Z zero work position (in a safe spot) do a air cut no tool in holder see how you go

1029
Newfangled Solutions Mach3 Wizards / Re: PHOTOvCARVE problems!!
« on: December 19, 2014, 10:14:20 PM »
your Z is fine no changes need to be made to your main set up just a couple of setting are set wrong  
I was wrong about Z home

1030
Newfangled Solutions Mach3 Wizards / Re: PHOTOvCARVE problems!!
« on: December 19, 2014, 09:46:46 PM »
its your setting that's the problem it does some trucked up things

some of your setting are wrong and you don't have anything useful in the initialization settings, hitting home all moves the z axis it should not do that and in general logic config you have ij mode set to Absolute it should be on inc.

I run a G540 as well I don't have the charge pump on you don't need to have it on

I will make some changes and repost it with a different name so you can just do a air cut test to see if it helps