Messages

1

General Mach Discussion / Re: Help with home switch setup.

« on: May 16, 2013, 05:23:53 AM »

Do i still need to set the debounce in Mach 3 at all now ?

2

General Mach Discussion / Re: Help with home switch setup.

« on: May 16, 2013, 05:21:10 AM »

Hi Tweakie,Thanks for help,i have just been reading an other post with the same problems and like the other guy i just discovered that because i am useing a smoothstepper i need to change it in the smootstepper settings so i will give that a go in the morning.Thanks again Chris.

3

General Mach Discussion / Help with home switch setup.

« on: May 15, 2013, 11:36:23 PM »

How do you set the amount an axis moves away from the home switch after it hits it when referencing as it is still activating the switch and throwing an estop.Thanks Chris.

4

General Mach Discussion / Re: Need help wiring a Keiling spindle and VFD

« on: April 12, 2011, 08:24:07 AM »

Thanks Tweakie,i don't know where you found that at,its at least a wiring diagram, more that i could get from Keling!maybe you should send him a copy.Thanks again Chris.

5

General Mach Discussion / Re: Need help wiring a Keiling spindle and VFD

« on: April 12, 2011, 08:05:09 AM »

It seams like there is no manual ! but i will try Peter tomorrow.Thanks.

6

General Mach Discussion / Re: Need help wiring a Keiling spindle and VFD

« on: April 12, 2011, 08:00:05 AM »

Thanks Hood,That is all out of my league i only wanted a spindle that was better then a router,this has been a nightmare!

7

General Mach Discussion / Re: Need help wiring a Keiling spindle and VFD

« on: April 12, 2011, 07:49:14 AM »

Hi guys,thanks for your help,can i use this without runing it through Mach3!

8

General Mach Discussion / Re: Need help wiring a Keiling spindle and VFD

« on: April 12, 2011, 07:03:48 AM »

Hi Hood,my VFD is a Keling KL-VFD22.Thanks for any help.

9

General Mach Discussion / Need help wiring a Keiling spindle and VFD

« on: April 12, 2011, 06:19:51 AM »

Hi guys,i have been going round in circles for weeks trying to get information from John about his products!I first contacted him weeks ago about weather i needed the VFD to run the 2200 spindle or was it just a normal 240v motor,and his reply was (240 volt)so i went ahead and ordered the spindle on its own as i would add the variable speed unit later.After several emails back and forth to john i finally found out that the spindle will not work without the VFD unit,so i ordered it and waited anoyher couple of weeks for it to arrive in Australia and now i still cant find out how to wire it up but now he tells me i need a C11 BOB to run it and my control box has a C10.Can anyone please help me with this as i dont think this is the answer either,somhow it has to get 240v from mains power to run it.Thanks Chris.

10

General Mach Discussion / Re: A newby trying to use a probe!

« on: April 10, 2011, 05:14:57 AM »

G'day Ian,I can't win! I changed the .csv to .txt and now when i start to do the 2.5 probe it stops and tells me a (type mismatch) and i can't get rid of it,i uninstalled your program deleted the download,deleted everything out of Mach3,deleted the folder in program files and any thing else i could find,but when i re-downloaded your program and set it all back up again it remembered all of my settings and just sent a (type mismatch) error again.Is ther somewhere else that it stores your settings.Thanks Chris.