Hello Guest it is May 09, 2021, 07:34:09 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Marcin81

Pages: « 1 2 3
21
General Mach Discussion / Re: Step motors problem - no movement
« on: March 27, 2011, 03:45:27 PM »
Great, thank you all for support !!!

22
General Mach Discussion / Re: Step motors problem - no movement
« on: March 27, 2011, 02:23:07 PM »
I do have, would you please give my some recommendations ? Just want to make sure I will buy the right card.

Thanks,
Marcin

23
General Mach Discussion / Re: Step motors problem - no movement
« on: March 27, 2011, 02:02:12 PM »
Hello,

I have tried to another PC and all works great, step motors moving. Is there a way to change output to 5V on my P Port or what I have to do to make the router work on my PC.

Thank you all for help !!!

24
General Mach Discussion / Re: Step motors problem - no movement
« on: March 27, 2011, 12:02:23 PM »
Hi,

I just opened the controller box and I found the name of the board which is TB6560-3V2. I will try to test on m friend PC now and see what will happen.

Thanks,
Marcin

25
General Mach Discussion / Re: Step motors problem - no movement
« on: March 27, 2011, 11:44:26 AM »
That looks good, now we tested the pins and the voltage is changing from 0V to 3.3V when I jog from - to +. It works for all X,Y,Z but nothing happening with the step motors.

Marcin

26
General Mach Discussion / Re: Step motors problem - no movement
« on: March 27, 2011, 10:35:19 AM »
I set all to be port 1 but still nothing. Also there is something strange with the pins on my PP sometimes they show 3.3V but sometimes 0V. Also when I jog there is very minimal change on the  voltage from 0.05V to 0.09V bit no movement at all.

Marcin

27
General Mach Discussion / Re: Step motors problem - no movement
« on: March 27, 2011, 09:49:42 AM »
I did new installation of mach3 and here is new xml file. The set up is as on the picture but nothing is changed so far. The parallel port dose not show bigger voltage the 3.3V on any of the pins.

Thanks,
Marcin

28
General Mach Discussion / Re: Step motors problem - no movement
« on: March 27, 2011, 08:27:07 AM »
Hello and thank You for reply,

I changed kernel down to 25 but nothing is happening. Also I have tried steps 1,2 and 4 as twieakie suggested but I am not sure which pins to check on my parallel port. The router is connected to PP on my motherboard. Also this is strange that the spindle is running when the reset button is flashing which is an emergency mode and If I am not wrong everything should stop when you press this button but here is the other way round the spindle start to run and the step motors start making buzz noise. Is not coming sens to me.

Thank You,
Marcin

29
General Mach Discussion / Step motors problem - no movement
« on: March 26, 2011, 10:26:07 PM »
Hello to All,

I just bought cnc router on ebay about 2 weeks ago and I can not get my step motors to spin. I am completely new to all cnc and I just spend last 6h on this forum to try to work out what may be wrong with my router but even on other posts with similar problem I could not find the solution so please help. Here is the link to the cnc that I bought http://cgi.ebay.co.uk/ws/eBayISAPI.dll?ViewItem&item=160554745917&ssPageName=STRK:MEWNX:IT
I already change my win7 to win xp as I thought that may be a problem but still no luck. I set up mach3 with the instruction that was on the cd with the router ( images in the attachment ). The motors are locked and make some kind of noise but they don turn at all. I also already try to play with different settings in mach3 but the motor didn't move when I press arrow keys to jog. Also the spindle is running and when I pres reset button it stops so looks like something is working but I have no more ideas how to get step motors to move. I appreciate any help.

Thank You,
Marcin

Pages: « 1 2 3