Hello Guest it is March 28, 2024, 09:38:18 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Jugster

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 »
51
General Mach Discussion / Motor Tune Graph
« on: November 08, 2014, 10:00:28 PM »
Hey Guy!!!

I remember having a problem once before and only being able to see one side of my motor tune graph.  I remember finding the solution to get it back where I could see it on the forum, but I can't seem to find it anywhere.  I remember it was simple.  All I can see is the ramp up in the motor tune profile.  Any help would be greatly appreciated!!!!
Thanks!!!!

52
General Mach Discussion / Re: New Machine A Few Bugs!!!!!
« on: October 21, 2014, 02:10:51 PM »
Had some help from Hood!!!!

53
General Mach Discussion / Re: New Machine A Few Bugs!!!!!
« on: October 20, 2014, 09:30:41 PM »
Brett,

After much double and triple checking, I'm going with CSMIO/IP-M  from CS-Lab.  Can't wait till it gets here. Thanks for the help.

54
General Mach Discussion / Re: CS-Labs Distributor
« on: October 20, 2014, 09:23:50 PM »
Scratch one project off the list and add five more!!!! :)

55
General Mach Discussion / Re: CS-Labs Distributor
« on: October 20, 2014, 07:33:22 PM »
I'll have an IP-S or A one day though.  Just don't tell my wife!!!!!!!!

56
General Mach Discussion / Re: CS-Labs Distributor
« on: October 20, 2014, 07:31:57 PM »
I went with IP-M.  My drives were capable of analogue and my heart was, but my check book fell just short!!!  I think all of us on here are on a tight budget!!!! LOL

57
General Mach Discussion / Re: CS-Labs Distributor
« on: October 20, 2014, 06:36:19 PM »
Alan,

I tried to do an online purchase last night. When I got up this morning I had a text message from them and we had the issue resolved pretty quickly. Hope there products are as good as there service!!!!  Not sure how long it will take to get here, but I can't wait!!!!

58
General Mach Discussion / CS-Labs Distributor
« on: October 19, 2014, 10:11:42 PM »
Any of you guys know if there is a US distributor for CS-labs products?  I looked on there website but didn't see any.  Didn't have much luck trying to place an order online either.

Thanks

59
General Mach Discussion / Re: New Machine A Few Bugs!!!!!
« on: October 16, 2014, 08:12:00 PM »
Brett,

That was my plan tonight.  It was very late when I posted.  I did receive some new files and plugins from the machine manufacturer last night.  I used everything that they sent me and I believe I have more problems now than I did before. >:(  I am debating on changing the bob on the machine with one that has some more support.  I replied to the machine manufacturer, and believe that they sent the wrong plugin, but I am running out of time to get this done.  Are any of you guys using the XHC-MK3 usb bob?  I saved all of my original set up files, and if I get time tonight I will change everything back and put a meter on the spindle out of the board.  Thank you for your help.

60
General Mach Discussion / Re: New Machine A Few Bugs!!!!!
« on: October 15, 2014, 10:41:14 PM »
Sorry Guys!!!  Here are the files!!!!

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 »