Messages

41

VB and the development of wizards / Re: activate the output to the desired position of the dro

« on: May 04, 2014, 06:54:32 PM »

Are Mach 3 can not read the "current line" and that is recognized in VB Script or brain control
eg  x200

42

VB and the development of wizards / Re: activate the output to the desired position of the dro

« on: April 28, 2014, 12:02:12 PM »

I should be close to the line of code with the x position
for example, x 400
x 500
....;;
depends on when it is activated input 1
                                                
G1 X400
G1X 500                         COMPARE    (g cod)   ANAS            ANAS
G1 X390      X POSITIO   ----- I<100 ---- x400----             ---          ---------OUTPUT 2
G1 X690                                       (g cod)       ANAS             Swich
.....              x position----- I > 50-----X 400---     ANA swich      /
.....                                                                                 /
.....                       INPUT 1 ---------------------------------------------/                      

43

VB and the development of wizards / Re: activate the output to the desired position of the dro

« on: April 28, 2014, 03:22:46 AM »

Yes this is the office that I used for some purposes, but I
I'm not good asked whether it is possible to compare the current line of G code to the current position and if eligible +100 -50 activates output 2.A for all that there should be a requirement that the active INPUT 1, so this can only happen when INPUT 1 is active
greeting

44

VB and the development of wizards / activate the output to the desired position of the dro

« on: April 27, 2014, 05:53:27 AM »

Please how do I compare the current position on the x-axis to display the default if it is in the range of eg +100 - 50 of the preferred activates output 2

45

Brains Development / Re: Using a DRO in a Brain

« on: April 26, 2014, 04:14:34 PM »

please how to write a macro and brain that will compare the current position of the x and y axes that use the bending machine with a default position that if the current position in the range of + - 50mm of default at the time when I have INPUT 1 one active program stops and activates OUTPUT 1
greeting

46

General Mach Discussion / Re: Operating a punch machine via Mach3

« on: June 24, 2013, 04:21:23 PM »

greeting
Are you able to insert the machine for breaking run with MACH3 I have the same one to do if your doing the experiences

47

VB and the development of wizards / VB to start\stop

« on: May 12, 2013, 07:50:27 AM »

Does anyone can help how to write vb script
for this example:
M2000 (that's my car 'z'i preparation start it works
G91 X400
M2001
X300
M2001
X200
M2001
X300
M2001 (You need to stop the program, to include (output1)
It touches the limit switch (input1) then off (output1) then when you touch the microswitch (input2) again pkrene program while ignoring (input1) until the next cycle.)
X690
M2001
M2002 (the script I returned the machine to the starting position and ready for a new cycle)
This is a machine for automatic cutting of the rear dimension of krojnoj list which can be interesting and I reworked the screen for one axis with potreblim commands

any help is welcome
Greeting

48

VB and the development of wizards / Re: LED indicator for optional stop M01 active

« on: May 11, 2013, 04:41:28 PM »

greeting
I have a problem when you put the M1 in the list of G codes it works but when I write it in a macro example
code "g1 x100"
code "M1"
code .........
then will not recognize it on one computer while on a machine to do what we can to be the cause
thank you

49

VB and the development of wizards / vb script tostart posirion

« on: March 31, 2013, 06:40:23 AM »

help
how to write a script to bring back the program before the last word of the line is a straight line of sewing and even if there is a mistake that could rupture the end of the program to start with the penultimate line and not at the last instance of engraving
thank you
aluplastvz@yahoo.com