Hello Guest it is March 28, 2024, 02:00:21 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - TRICKEY

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 »
21
  ;D
Hi Phil welcome aboard  thanks for dropping by and introducing your self, it's great that you find the discussions stimulating and informative that is what this Group is all about, shared knowledge, everybody that joins brings something with them, that when shared will help some one else,None of us came into this world knowing everything.
Working for a small company has many rewards, and wearing 20 hats is a good thing, you don't have free time to get bored.
Regards       
  Dick  ;)

22
   ;D 
Hi Guy welcome aboard, you certainly have a lot going on in your life,sounds like you are starting up your own army.
Thank you for dropping by and introducing your self.

  Regards
     Dick  ;) 

23
   ;D
Hi Dennis welcome aboard, thank you for dropping by and introducing yourself, I can understand your excitement,to be starting down the all consuming path of knowledge,
This thread is purely a introduction site,all questions should be addressed to the"General Mach Discussion"area which is accessibly from this page just brows the threads and post any questions on an appropriate site I'm sure that you will get  help from the many knowledgeable members.
Regards
 
  Dick  ;)
   

24
   ;D
Hi Frank welcome aboard I can appreciate where your coming from,I hate to see functioning machinery laying idle, taking up valuable space and perhaps not utilising employees to their full potential,bad management, my philosophy was always to  multi skill employees, a win win situation better for company production and a higher morale for staff. ???
That's my soapbox for the day.
This is solely a introduction site and thank you for dropping by and introducing yourself
If you address your questions to the GENERAL MACH DISCUSSION area, accessible from this page, brows the threads and select one that sound closest to your needs
I wish you well in this project

  Dick ;)                 

25
   ;D
Hi Flying Dutchman and Suggs welcome aboard thanks for dropping by and introducing your selves to us seeking knowledge in itself is a very rewarding part of any new venture
This is primarily an introduction site and all questions should be addressed through the General Mach Discussion area
which is accessible from this thread I'm sure that you will receive answers your looking for
 
wish you well in your venture
 Regards
   Dick   ;)
 
           

26
   ;D
Hi Guys welcome aboard my Wife and I have been  away for a few days so I have not been around to welcome you all so this will be a joint welcoming,
This is a introduction site and all questions should be addressed to the General Mach Discussion site just brows the brows the various threads and find one that would be closest to your requirements,there is a vast amount of knowledge on all the sites and I know that they will be of help

  regards
  Dick  ;)   

27
   ;D
Hi Raul welcome aboard thanks for introducing yourself It is always great to hear from new members, every new member that joins brings something with them,and you never know how many other members benefit from the questions of others
 this is a shared help group and there will be a time that you will be able to assist some other member,the old theory about the wheel that goes around, ::)
    Us boys must have our toys
 
   Dick  ;)

28
General Mach Discussion / Re: New PlugIn just about done..
« on: March 17, 2012, 12:23:35 PM »

Thanks Dave went out and followed your instructions ever thing worked out fine
if ever you come down under here to OZ I owe you a beer  ;)

Dick

29
General Mach Discussion / Re: New PlugIn just about done..
« on: March 17, 2012, 06:28:20 AM »
 ::)
Thank you very much Dave I just could not get my head around this on my own. ??? just getting old I guess

   Dick

30
   ;D
Hi Drew welcome aboard  thanks for dropping in and introducing your self.
unfortunately this is purely a introduction site and any technical questions should be addressed to the GENERAL MACH  DISCUSSION threads which can be accessed from this page, just brows the threads an select one that seems closest to the topic that you are seeking the answers to

   Dick  ;)

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 »