Messages

51

NC Pod / Re: Report Any NC Pod Driver, Firmware or Documentation Download Problems Here

« on: February 13, 2007, 09:11:39 PM »

I cannot understand a Universal Serial Bus port.
Is "ncpoddriver.zip" "an USB2.0" driver of "ncPOD?"
Communication of "ncPOD" needs "USB2.0".
"USB2.0" is not prepared for "Windows 2000".
An application producer prepares a driver generally, but where can demand it?

52

NC Pod / Re: Report Any NC Pod Driver, Firmware or Documentation Download Problems Here

« on: February 05, 2007, 09:30:55 PM »

This is my setings for inputs. For home inputs I don't believe the pin number is important only enable and port number.

Do you carry out the label of the setting screen, and can get it about an Estop input or six outputs? He cannot understand explanation of ncPOD, and inconsistency of regulation of MACH3.

53

NC Pod / Re: Report Any NC Pod Driver, Firmware or Documentation Download Problems Here

« on: February 05, 2007, 04:14:01 AM »

Thank you.
I study an image of the setting that you told it about.

54

NC Pod / Re: Report Any NC Pod Driver, Firmware or Documentation Download Problems Here

« on: February 04, 2007, 04:49:15 AM »

Thank you for giving an answer to me. My native language is not English.
I use an interpreter, and expression is not correct.
"Setting" of "port 's" and "pin 's" of MACH3 gets very tangled with a manual of "ncPOD".
Please show an example of "setting" to me.
It hopes for six axes and Estop, Homes, motor,step,dir from three axes.

55

General Mach Discussion / Re: Mach to DeskCNC?

« on: February 02, 2007, 11:39:43 PM »

About ncPOD.
It is mentioned as follows.
An NCPOD base has a SD card and can memorize a program, and any kind of capacity of a SD card is OK by operation from 2.0 USB com interface.
I have manufacturing time of about 30 seconds per 1MB.
A SD card of 256MB carries out manufacturing of about 2 hours.
iPart is completed even if Host computer loses communiactionsj.
A question.
Does not MACH3 use internal SD memory?
In addition, does not NCPOD have a G code compiler inside?

56

NC Pod / Re: Report Any NC Pod Driver, Firmware or Documentation Download Problems Here

« on: February 01, 2007, 07:57:31 PM »

Follows are communication from my friend.
”I tried to move it in NncPOD and Mach3 today.
How to change courses of a motor does not understand that I noticed.
I do not understand setting of a home.
A limit is not usable.
I could confirm a limit and movement of a home with a ncPOD screen of Mach, but was not usable.
The navel orange (the 14th pin) of a sea bream and the spindle oil (the first pin) worked moo well.
Connection cut inside audio system cable for PCs in half and tied connection of other users to reference in a D assistant 25 pin male.
I stopped when I really carried out maximum around 200 lines G code with the button 所 "libretto U100" laptop that I tried to let you process it. It was able to process it in SC430 of "Dell" which was in a condition where there was not E-STP cancellation unless I rebooted Mach and ncPOD after stopping to there there, but stopped afterwards in the place that said a little more.
A connection method
http: //221.132.159.78/forme/up/ncPOD/00.pdf
Setting of Mach
http: //221.132.159.78/forme/up/ncPOD/Mach3Mill.xml
I appear and do it.”

57

NC Pod / Re: Report Any NC Pod Driver, Firmware or Documentation Download Problems Here

« on: February 01, 2007, 08:51:03 AM »

I downloaded "Mach3 R2.00.041" and installed it.
A new version is displayed with "Version R2.0.040".
A firm ware version of NCPOD is displayed with "2.0.038".
I deleted "the latest Microsoft .net framework" once just to make sure and installed it again.
I prohibited Legacy USB by BIOS and rebooted.
It is expected that MACH3 and USB communication of an NCPOD board are ready, but cannot complete movement.
It is displayed with USB library:usb_bulk_read endpoint 2byte=116:usb_reap:timeout err.
I suppose that I use six "Mach3Mill" axes for me, and please show an example of Kon Figg military ration of "a port and a pin".

58

NC Pod / Re: Welcome To The NC Pod Development, Discussion and Support Topic

« on: January 29, 2007, 10:26:46 PM »

I use "ncPOD/F2014" and "Mach3VersionR2.00.040".
I want to operate it in "six axes".
Please show "an example" of Kon Figg military ration of "a port and a pin" in MACH3.
Do these work by "win2000"?

I knew that "Mach3VersionR2.00.041" was the latest.
I want to know whether "only my ncpod" does not work or whether even some people do not work.
I write it here so that tested present status becomes a part in knowledge of an author.
I pray so that "MACH3" and "NCPOD" develop into me, and it is loved by a lot of people.

In addition, support firm ware of USB is perfect early; expect it to become it.
When an author announces present status, I cannot be troubled.