Messages

11

NC Pod / Re: status of NCPod

« on: May 20, 2009, 09:59:08 AM »

Hi. MR "kuromaku"
Is it true?

What is the meaning of the wirepuller? .
a black curtain.
a wirepuller.
pull the wires.

12

NC Pod / Re: Welcome To The NC Pod Development, Discussion and Support Topic

« on: December 04, 2008, 09:38:15 PM »

Hi
I get an NC code used for drive of a thing of this movie and can try it?
"www.cncteknix.com/video/motiontest.mpg"

Is there a method to send off from method and MACH3 to write in at a direct SD card sequentially to operate ncPOD?
（The movement of MACH3 is felt so that CPU movement can afford by USB-ncPOD way）

In addition, is there the cord about the exercise of four axes?
（I hope for a method to write in at a direct SD card）

The direct note cord which I made becomes the error and does not work.
（Is there clear grammar somewhere?）

13

NC Pod / Re: What is this??

« on: December 03, 2008, 10:54:23 PM »

Were you able to complete the update of the firm ware in the part on this image?
The next image applied ".set of the form cutter" to "ncPODUpdater2031.zip" and "MACH3".


"ncPOD" which I have has two or three software forms, but cannot manage it enough because those detailed explanation is not done.

14

NC Pod / Does ncpod live?

« on: December 02, 2008, 08:59:12 PM »

Hello, do you know the next thing?

I operate "ncPOD" in "MACH3".
When it applies "ncPODUpdater2031.zip" and "DeskPod.m3p", "ncPODUSBDriver.zip" and operates it, it is displayed like four axes and works according to a sample.
However, is the next function necessary to work as a stand alone unit?
There are other method "ncPODSetup.exe" (completeness is high) and "OEMTechDeskPodControlPanel 1.0.0.0.exe" (there are incomplete movement, an error), and each is two kinds of display units.
I cannot operate them.
I request it for the procedure of the reading note for the SD memory which I attached to ncPOD.

I do not understand whether there is me in the ncPOD inside whether there is a function to convert "NC-DATA" into a pulse of ncPOD to a host computer.
It is the doubt of the function whether it records NC-DATA and converts whether the SD card which I attached to ncPOD records pulse information as for this into a pulse with a processor of the ncPOD inside.
Alternatively, it is setting means about the input/output of the ncPOD system.
It is not possible for measures and emergency such as the reboot and the judgment of the limit, and ncPOD will not work for an independent device where there is the command if there is it because I can reverse setting if there is not this.

I contact a producer to be next and want to make it clear about those contents.



I want to evolve earlier to have already come to here.
You advance to only it early if you support it more.

15

NC Pod / Re: ncpod locked

« on: October 30, 2008, 12:02:40 AM »

Hi
The best method that you have sends an image of the update failure of the firm ware to the purchase place, and it is to hear the measures method of the fault.
Be settled.

16

FAQs / It is a question about application of MACH3.

« on: September 05, 2008, 08:26:22 AM »

Is there the most suitable panel to operate four axis form heat rays cutters?

17

NC Pod / How is he?

« on: May 28, 2008, 12:45:50 PM »

hi, everyone. Him (ncPOD-OEMTEC) you know thing who? If he has lived, appearing in this place, story should be done, with you don't think?

18

NC Pod / Re: LIMIT SWICHES

« on: April 21, 2008, 09:59:56 AM »

I am a Japanese.
I do not understand English.
If you report the present conditions by simple words little by little, I understand it little by little and, in a possible range, can reply it.
Your question content is difficult and may not answer it.
Please forgive it then.

19

NC Pod / Re: ncpod locked

« on: February 26, 2008, 06:32:40 AM »

It is not found a good method in me.
When I was connected other than "USB 2.0" once, perhaps I write in a wrong "cord" at "firm ware" and will not do it.
I cannot reply to the later transmission and reception definitely and cannot continue.
The cause may be because he is too busy.
I have information about little solution, but cannot show it.

20

NC Pod / Re: How to download the sequence of code into SD RAM

« on: January 16, 2008, 08:49:30 AM »

Because it is the question in this page, I suppose it to use "2031 ncPod Firmware Installer (Version) for Mach3 or Basic Control Panel".
Did you do movement by "the G code" or the data transmission of a message from "Mach3?"

I was inappropriate, but did confirm it in movement with "only ncPod Basic Control Panel 1.0.0.0" to discuss it here?

It is assumed that you have already used next.
incPod USB Driver(Only needs to be installed once)j