Topics

1

General Mach Discussion / LINUX ?

« on: August 11, 2012, 11:42:09 PM »

Hello
Raspberry Pi is LINUX.
Do you think this is subject to the mach3?
Sincerely yours

2

Feature Requests / Please tell me the information of the device like a lathe.

« on: June 03, 2012, 01:21:14 AM »

Hello.
I plan a winding machine of the electric wire.
The electric wire winding machine resembles a lathe closely.
A central organization is to the right direction from the left.
The turn of the main shaft begins slowly and stops 100 rounds or 1,000 rounds in the place that I went around.
There is another winding forwarding axis and is parallel to a main theme.
Electric wire guidance metal fittings are attached to it.

After having sent it approximately 10mm, the electric wire guidance metal fittings return to the opposite direction approximately 10mm.
When the winding comes to the slant direction to a main shaft to the edge with the winding, I coil myself around the opposite direction diagonally.
Coil yourself using gaps fewer than a winding before (I repeat this) (do not have a line and coming at the same time) and continue in movement.
I wind the predetermined number of times and I glue the edge of the winding together when completed and end operation.

A characteristic of this machine is that a central figure does a large number of turns in the same way as a lathe.
I do another electric wire forwarding axis by the end when they come in the case of a screw box to the edge, but, as for this device, coming and going work in right and left many times.

Please tell me it if I know the method that axis-related setting of such a machine and how to make cords are useful for.
Yours sincerely,.

Thank you.

3

SmoothStepper USB / Please answer the questions correctly.

« on: December 20, 2011, 08:54:31 PM »

Dear Warp9 Tech Design

I'm going to have questions and input and output numbers assigned as follows: Breakout Board.
"On 12/14/2011 2:33 AM, Kyoji Nonomura wrote:
This is an enquiry e-mail via http://www.warp9td.com from:
Kyoji Nonomura

Dear Warp9
I want to change the functionality of the device.
If you have a comparison table of numbers and pin numbers MACHPIN Breakout Board, I can make a connection.
Motor is connected XYZA
2,3, COM,
4,5, COM
6,7, COM
8,9, COM
But as we understand,
Otherwise I'm not sure about the pin.
Please tell me if you have a terminal connection arrangement table.
Best regards
"
But you come to the window of the USB driver updates for your reply What is?
"Dear Kyoji Nonomura,

I am forwarding your message to Tech Support (support@warp9td.com) where
Greg will be able to address it.

In the future, please write directly to support@warp9td.com when you
require Technical Support.

Kind Regards,
Stephanie
--------------
Stephanie Cary
Customer Sales
Warp9 Tech Design
sales@warp9td.com
www.warp9td.com "

Best regards

4

NC Pod / I have tested on several samples

« on: December 20, 2011, 05:25:35 AM »

Results of the 2031 update

Installing the SD Memory
S/N Number power of USB_BUS RNumber Display character

S/N 1017  5V power jumper Error! try again update 28 0% NG
S/N 1035  5V power jumper Error! try again update 28 0% NG
S/N 1044  5V power jumper Error! try again update 28 0% NG
S/N 1038  5V power jumper Error! try again update 28 0% NG
S/N 1043  5V power jumper Error! try again update 28 0% NG

S/N 1678  R228 Error! try again update 25 41% NG
S/N 1642  R48 Error! try again update 25 50% NG

S/N 1641  R168 31 0% OK
S/N 1675  R204 31 0% OK
S/N 1667  R276 31 0% OK
S/N 1671  R168 31 0% OK
S/N 1672  R240 31 0% OK
S/N 1674  R240 31 0% OK

5

NC Pod / Does ncpod live?

« on: December 02, 2008, 08:59:12 PM »

Hello, do you know the next thing?

I operate "ncPOD" in "MACH3".
When it applies "ncPODUpdater2031.zip" and "DeskPod.m3p", "ncPODUSBDriver.zip" and operates it, it is displayed like four axes and works according to a sample.
However, is the next function necessary to work as a stand alone unit?
There are other method "ncPODSetup.exe" (completeness is high) and "OEMTechDeskPodControlPanel 1.0.0.0.exe" (there are incomplete movement, an error), and each is two kinds of display units.
I cannot operate them.
I request it for the procedure of the reading note for the SD memory which I attached to ncPOD.

I do not understand whether there is me in the ncPOD inside whether there is a function to convert "NC-DATA" into a pulse of ncPOD to a host computer.
It is the doubt of the function whether it records NC-DATA and converts whether the SD card which I attached to ncPOD records pulse information as for this into a pulse with a processor of the ncPOD inside.
Alternatively, it is setting means about the input/output of the ncPOD system.
It is not possible for measures and emergency such as the reboot and the judgment of the limit, and ncPOD will not work for an independent device where there is the command if there is it because I can reverse setting if there is not this.

I contact a producer to be next and want to make it clear about those contents.



I want to evolve earlier to have already come to here.
You advance to only it early if you support it more.

6

FAQs / It is a question about application of MACH3.

« on: September 05, 2008, 08:26:22 AM »

Is there the most suitable panel to operate four axis form heat rays cutters?

7

NC Pod / How is he?

« on: May 28, 2008, 12:45:50 PM »

hi, everyone. Him (ncPOD-OEMTEC) you know thing who? If he has lived, appearing in this place, story should be done, with you don't think?

8

General Mach Discussion / Is it the movement speed of the system?

« on: July 19, 2007, 10:13:47 PM »

I operate MACH3, and it sometimes happens that the drawing speed of the computer puts away very late when finished afterwards.
Can you easily return this normally?
What are these causes?

9

Screen designer tips and tutorials / A general question

« on: May 01, 2007, 11:31:32 PM »

A general question.
In the end back, indication of GUI becomes very slow after having started MACH.
I am restored when I reboot a computer.
Is there a method to return without rebooting?