Hello Guest it is March 28, 2024, 06:40:19 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - renatom

Pages: « 1 2 3 4 »
11
General Mach Discussion / Re: Properly doing "Run Frome Here"
« on: June 30, 2010, 06:08:24 AM »
Hi Peter,

Sorry I was not very attentive to the  Question, The Gcode contains Both M70 and M71  before RFH line. M71 will turn the output first then will run a line depending on the program then M70 will be called to disable the output


Thanks
Renato

12
General Mach Discussion / Re: Properly doing "Run Frome Here"
« on: June 30, 2010, 05:02:53 AM »
Hi Peter,

M71 tuns on output1 and M70 turns off output1 in a Gcode program.

Thanks
Renato

13
General Mach Discussion / Re: Properly doing "Run Frome Here"
« on: June 30, 2010, 02:20:33 AM »
Do you know when Rev4 is going to be release?

Thanks
Renato

14
General Mach Discussion / Re: Properly doing "Run Frome Here"
« on: June 29, 2010, 07:15:28 PM »
Hello Hood,

I have tried SET NEXT LINE this morning and seems to be working. I will do a bit more testing. Thank you for the Idea. I still have one last question if you could Please give me a starting point on the best way to deal with tool offset.
I have 5 router heads on the Z axis  and individually turn on. Which is the best way to Do individual   OFFSET on  all four Spindle Motor to the first Motor? I know i am asking too much but dont know where to start at this stage.

Thanks again

Renato


15
General Mach Discussion / Re: Properly doing "Run Frome Here"
« on: June 29, 2010, 07:07:05 PM »
Hello Peterf

Thanks again for the help. Yes M71 executes properly when called on a GCODE program. But M71 turns on and OFF when RFH. I forgot to mention that M70 turns OFF M71. Its similar if you tick off the option under general config  IGNORE M CALLS WHILE LOADING and you load a GCODE Program. Sorry I did not quite understand what you meant by "RACE".  If there is an OEMButton that will do "Ignore M calls while loading "it will fix the problem....Thanks in Advance

Regards
Renato

16
General Mach Discussion / Re: Properly doing "Run Frome Here"
« on: June 29, 2010, 04:57:44 AM »
Hello  hood,

Thanks for the information, I will try that option tomorrow morning and will let you know.

thanks for the great support
Renato

17
Brains Development / Re: Should a Brain disable a Macro
« on: June 29, 2010, 04:53:56 AM »
hello Scott,

Thanks for the reply. I was able to find a solution to fix the problem.

Thanks for the support
Renato

18
General Mach Discussion / Re: Properly doing "Run Frome Here"
« on: June 29, 2010, 04:25:44 AM »
Hi Hood,

I have seen that Option on General config and works only When Loading The program but doesnt apply on RFH. That option is the solution if it Works with RFH. If that option is not ticked on General Config, It will be doing the same thing as RFH when loading Gcode program all the Macro are Triggering. I hope that option will be available as a command. Thanks for your Help


Thanks Again
Renato

19
General Mach Discussion / Re: Properly doing "Run Frome Here"
« on: June 28, 2010, 09:11:51 PM »
Hi Hood,

Thanks for the reply. I think that will be the case. Macro M71 turns on a Solinoid Pneumatic Valve and its turning on and OFF during the run of RFH. I think i will not be able to use RFH. Would there be a command that I could disable Macro while on RFH so I could edit the Button Script of RFH and prevent Macro from excecuting?

Thanks Again
Renato

20
General Mach Discussion / Re: Properly doing "Run Frome Here"
« on: June 28, 2010, 07:51:37 PM »
Hello Peter, Gerry,

Thank you very much for the Reply. I have a full license Mach 3 So is not on Demo Mode. What I meant is one of My Macro(M71) is turning an Output1. When I run RFH and its scrolling Down I have notice that Output 1is turning on while reading the file up to the point that it reaches the line where I want to start. Just need an advice if this is the way it should work. Thanks again.

Regards
Renato

Pages: « 1 2 3 4 »