Hello Guest it is March 29, 2024, 10:20:26 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - BR549

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 »
6391
General Mach Discussion / Re: Mach did again!
« on: September 30, 2010, 10:23:09 AM »
1 question,  When this last happened and MACH wondered off, did you see the wandering off in the toolpath display as well? AND did the dros show that it had wondered off the programed toolpath?

Have you tired to reload a known good backup of the XML?

IF you do not have one build a brand new XML from scratch using all the setup info that you have in your old one.

IF that does not work then do a completed reload of mach.  BUT FIRST document precisely how it happens NEXT TIME it does it

IT is important when testing that you do not jump around doing a lot of different things at the same time. ONLY a methodical test approach will find your problem. NOTES as Hood said LOTS of noted describing each step you take. AND do them them one step at a time.

You explanation is somewhat all over the place as Hood said.  Settle down and we can get to the bottom of the problem.

(;-) TP

6392
Feature Requests / Re: Formula for variable feedrate
« on: September 28, 2010, 11:26:41 PM »
YOu could make a brain that monitors and compares the Y position then alters the Feedrate Override based on the % of change of the Yposition.

BUT remember it will alter the feedrate on ALL axis not just X.

Just a thought, (;-) TP

6393
General Mach Discussion / Re: thc in macropump
« on: September 28, 2010, 09:35:04 PM »
I think you should be able to just map the 2 signals as inputs directly to the thcup  and thcdown functions in config. Maybe NO code needed

Just a thought, (;-) TP

6394
YOU have alot of things going on at once(;-). YOu may want to move the G41 inside of the SUB. AS is you have the G41 in effect in G90 mode then switch to G91 mode probably confused MACH.

Notice that the the Next G1 move after your G41 is the same line you have taper. Mach needs to have a move to comp the toolpath BEFORE it gets to the start point of the offset and it needs to be at least the same length as the radius you are comping(depending on version) SO it looks like MACH is using the move to comp itself ending up as a taper???



Just some thoughts, (;-) TP

6395
IS this Mill or Turn code??? YOu mention grinder wheel radius.

(;-) TP

6396
General Mach Discussion / Re: thc in macropump
« on: September 27, 2010, 10:09:50 PM »
You might want to look at the  Mach  THC plugin. 

(;-) TP

6397
VB and the development of wizards / Re: Macro M6 safety
« on: September 27, 2010, 09:57:37 PM »
WHo did the original Macro?? That would be a good place to start looking for help.

Just thought (;-) TP

6398
General Mach Discussion / Re: New MHP mill project
« on: September 27, 2010, 09:31:53 PM »
IF I had a full function Machine center with toolchanger running I would look into the servo problem first. It may be a simple loose wire or bad encoder.

Just a thought,(;-) TP


6399
General Mach Discussion / Re: BUTTON QUESTION
« on: September 26, 2010, 12:32:28 AM »
ITS NOT TO RUN ANY CODE IS JUST TO CONVERT A PC ON A HIGH SPEED (45KHZ) STEP GENERATOR FOR A CUSTOM MACHINE WICH USES AN STEPPER MOTOR TO MAKE ITS WORK,

** OK


ALSO IS IT POSSIBLE TO JOG ALL X,Y,Z,A,B,C AND HAVE INDEPENDENT FEED CONTROL ON EACH

** NO


 OR JUST A GENERAL FEED CONTROL FOR ALL OR THE ONES THAT YOU ACTIVATED TOGETHER FROM 1 TO 6?

** SORTA

6400
General Mach Discussion / Re: feed hold button
« on: September 26, 2010, 12:27:42 AM »
It is NORMAL for any buffered system. Mach has to plot a solution to create an end point then safely bring the system to a halt inside of the axis tuning parameters so you do not loose position, no lost steps.

So depending on your lookahead settings it may take mach a few moves to come to a safe stop.

It is NOT a safety concern. IF you need to STOP immediately then STOP or Estop  not feedhold (;-)

(;-) TP

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 50 51 52 53 54 55 56 57 58 59 60 61 62 63 64 65 66 67 68 69 70 71 72 73 74 75 76 77 78 79 80 81 82 83 84 85 86 87 88 89 90 91 92 93 94 95 96 97 98 99 100 101 102 103 104 105 106 107 108 109 110 111 112 113 114 115 116 117 118 119 120 121 122 123 124 125 126 127 128 129 130 131 132 133 134 135 136 137 138 139 140 141 142 143 144 145 146 147 148 149 150 151 152 153 154 155 156 157 158 159 160 161 162 163 164 165 166 167 168 169 170 171 172 173 174 175 176 177 178 179 180 181 182 183 184 185 186 187 188 189 190 191 192 193 194 195 196 197 198 199 200 201 202 203 204 205 206 207 208 209 210 211 212 213 214 215 216 217 218 219 220 221 222 223 224 225 226 227 228 229 230 231 232 233 234 235 236 237 238 239 240 241 242 243 244 245 246 247 248 249 250 251 252 253 254 255 256 257 258 259 260 261 262 263 264 265 266 267 268 269 270 271 272 273 274 275 276 277 278 279 280 281 282 283 284 285 286 287 288 289 290 291 292 293 294 295 296 297 298 299 300 301 302 303 304 305 306 307 308 309 310 311 312 313 314 315 316 317 318 319 320 321 322 323 324 325 326 327 328 329 330 331 332 333 334 335 336 337 338 339 340 341 342 343 344 345 346 347 348 349 350 351 352 353 354 355 356 357 358 359 360 361 362 363 364 365 366 367 368 369 370 371 372 373 374 375 376 377 378 379 380 381 382 383 384 385 386 387 388 389 390 391 392 393 394 395 396 397 398 399 400 401 402 403 404 405 406 407 408 409 410 411 412 413 414 415 416 417 418 419 420 421 422 423 424 425 426 427 428 429 430 431 432 433 434 435 436 437 438 439 440 441 442 443 444 445 446 447 448 449 450 451 452 453 454 455 456 457 458 459 460 461 462 463 464 465 466 467 468 469 470 471 472 473 474 475 476 477 478 479 480 481 482 483 484 485 486 487 488 489 490 491 492 493 494 495 496 497 498 499 500 501 502 503 504 505 506 507 508 509 510 511 512 513 514 515 516 517 518 519 520 521 522 523 524 525 526 527 528 529 530 531 532 533 534 535 536 537 538 539 540 541 542 543 544 545 546 547 548 549 550 551 552 553 554 555 556 557 558 559 560 561 562 563 564 565 566 567 568 569 570 571 572 573 574 575 576 577 578 579 580 581 582 583 584 585 586 587 588 589 590 591 592 593 594 595 596 597 598 599 600 601 602 603 604 605 606 607 608 609 610 611 612 613 614 615 616 617 618 619 620 621 622 623 624 625 626 627 628 629 630 631 632 633 634 635 636 637 638 639 640 641 642 643 644 645 646 647 648 649 650 651 652 653 654 655 656 657 658 659 660 661 662 663 664 665 666 667 668 669 670 671 672 673 674 675 676 677 678 679 680 681 682 683 684 685 686 »