Messages

3281

General Mach Discussion / Re: BT30 spindle from scratch - with power drawbar and ATC of course

« on: January 04, 2013, 09:55:13 PM »

You could push Light hydraulic fluid(ATF) instead of air .

Just a thought, (;-) TP

3282

General Mach Discussion / Re: New years resolution

« on: January 04, 2013, 08:28:41 PM »

BOB that is the very spirit of the MachSupport Forum (;-)  From Unknowing to learning to helping others.

(;-) TP

3283

General Mach Discussion / Re: Staying with the same (0,0,0)

« on: January 04, 2013, 02:50:23 PM »

Just build a locating  JIG to hold the part at location.

(:-)TP

3284

General Mach Discussion / Re: material translation matrix

« on: January 04, 2013, 12:02:28 PM »

Check this out for Warp Matrix

http://www.youtube.com/watch?v=0jGY92S8bxM

(;-) TP

3285

General Mach Discussion / Re: BT30 spindle from scratch - with power drawbar and ATC of course

« on: January 04, 2013, 11:40:45 AM »

Nice try stevo BUT " your" words proved my point .   IF you look back through your posts the main objective was to sell someone on the site your wares. AND it was hard to sell your wares to Tormach users as long as Tormach LOCKED you out of the picture.  Then you were pissed because Greg would NOT work with you so you could access his customer base

Then there is the ME syndrome. Basic genetic flaw in a LOT of engineers who think the world cannot revolve without their guidance.

I dought that Greg needs your help with anything concerning his CNC products. He is light years ahead of you already .

But you Have a good one anyway, YA hear

(;-)TP

3286

General Mach Discussion / Re: material translation matrix

« on: January 04, 2013, 04:53:00 AM »

ANY ideas on a Transformation matrix where you scan the material then Process the Gcode Z axis to fit the material. ? One controller I have seen has it working . The demo was impressive to say the least.

(;-) TP

3287

General Mach Discussion / Re: DeskEngrave WIZARD

« on: January 04, 2013, 04:25:12 AM »

Added some more features such as partscale and xy extents so you can see the SIZE of the engraving and adjust if needed.

Took a while to find enough VB code to make the shell out and back work correctly and some more time to find enough code to make the auto file load work with DeskEngrave.

Hopefully it Should be usefull to those who engrave.  Does arc and angle and straight  ,  Scale up and down

(;-) TP

3288

General Mach Discussion / DeskEngrave WIZARD

« on: January 03, 2013, 10:40:35 PM »

HIYA DUDES, I figured out a easy way to USE Deskengrave from inside a Mach3 Wizard. The results is you can create your Engraving code from ANY system FONT then import it into Mach3 FROM the Wizard. From there you can run the Engrave Gcode.  

Not sure it would be handy but it appears to be from here.

What do yall think ? worth finishing up???

(;-) TP

3289

General Mach Discussion / Re: como poder subir o bajar el eje z mientras se ejecuta un codigo es para oxicorte

« on: January 03, 2013, 09:59:19 PM »

Yes you can, do a search on thcup() thcdown()

(;-) TP

3290

General Mach Discussion / Re: New years resolution

« on: January 03, 2013, 06:50:34 PM »

Thanks to all the document writers of Mach3 over the years, and then ART said (;-)

(;-) TP