Messages

1

General Mach Discussion / Re: Mach3 Problem whit 2 boallscrew on Yaxis

« on: September 25, 2014, 06:14:31 PM »

i have fix the problem

2

General Mach Discussion / Re: Mach3 automatic tool changer

« on: September 25, 2014, 06:14:00 PM »

all  ok i fix the problem

3

General Mach Discussion / Mach3 automatic tool changer

« on: September 25, 2014, 11:34:01 AM »

Hi

I am set up my ATC 

now if i run the macro with

Vb scripter window  the machine  is working ok   

but  if i go  to MDI and i call  for tool change T2 M6  or other  tool the machine does not respond  ( not  working )

what i have wrong

Thanks Komra

4

General Mach Discussion / Mach3 Problem whit 2 boallscrew on Yaxis

« on: September 23, 2014, 05:35:47 PM »

Hi

I have  cnc router  whit 2 ball screw on Y axis

i have slave axis  on Y to A

and now if i  ref all home  one of the Y axis ball screw is not working one that is slave to A  what can i do

thanks for help 

Komar

5

General Mach Discussion / Re: Neet help with driver 1545

« on: November 01, 2013, 09:30:31 PM »

Hi Rich
I do not understand with these numbers  I do not know what these numbers mean can you please tell me ?
- For SW 5,6,7, use 1/10 Microstep setting as there is nothing to be gained by going higher.
- For SW 1,2,3 use 2.7 Amp setting ( you can go to 3.2 or 2.3 , test and see how the motors react)
-  FOr SW 4 use full current


 Thank you for your reply

6

General Mach Discussion / Re: Neet help with driver 1545

« on: November 01, 2013, 09:25:38 PM »

Hi sir
yes i am using parallel port  C10 breakout board

7

General Mach Discussion / Neet help with driver 1545

« on: October 31, 2013, 05:28:30 PM »

Hi please help me  to setup mach3 with with this driver
my stepper motor is

2.6 Nm  Hybrid Motor  368oz
1.8° /200 Steps Per Rev.
3.5 Amps Current Per Phase
Inductance 2.8 mH
4-wire Bi-polar,    

ball screw  pitch 5 mm

I am working  with mm

thanks for  help

8

General Mach Discussion / Re: i have a problem with rhino cam 2.0 5 axis.

« on: April 27, 2012, 07:54:18 PM »

next question mecsoft.com
If there is anyone who can verify this Please help

There is no sample g-code for 5 axis included - is there any where we can find this, we should be able to create a post once we make sure the primary & secondary axis definitions are correct.

When I talked to Peter, I was told  the secondary axis sits on top of primary (X) and rotates 360 degrees.  If this is the case, then when the primary axis is at A=0, the secondary axis rotates parallel to Z axis. (as shown below). I would like to know if this is how the primary & secondary axis are setup

9

General Mach Discussion / Re: i have a problem with rhino cam 2.0 5 axis.

« on: April 27, 2012, 12:37:34 PM »

They ask me about this


> 1. 5 axis machine configuration (Head-Head / Table-Head/ Table-Table)/ --- we know this : Table-Table is your configuration./
> 2. Information on Primary and Secondary axis.
> (For example: A head-head configuration, the Primary axis is about Z axis and the Rotation axis code is represented by the letter "C' and secondary axis is about Y axis, rotation axis code , is represented by the letter "B")
> 3. G & M code specifications from the controller manual
> 4. Information on canned cycles for drilling, tapping, boring operations, (G81 - G89)
> 5. Arc output formats for Circular interpolations (G02/G03),
> 6. Start and End Block information
> 7. Tool Change definition
> 8. A sample g-code that has 5th axis

answer  if someone will notice some mistake, correct please

1.) Table - Table
2.) Primary axis I think would be about the X  axis (A) and the secondary axis would be about the Y axis (B)
3.) Standard G and M  codes will be fine. If you need more I have attached a file for you with the G and M codes
4.) See attachment
5.) See attachment
6.) Standard safe startup block will be fine ( "G80 G40 G00 G50 G90" ) at the end of the file you only need to have an M30
7.) Tool change is only the tool number and M6 So to change to tool 5 you would have the following line "M6 T5" . Tool length offsets are activated by doing a G43 H<height register> (Like Fanuc)
8.) I don't have any 5 axis files here but I would be willing to simulate them here to see if there are any problems.  A 5 axis move would be "G91 G0 X 1.0 Y1.0 Z1.0 A1.0 B1.0"


If someone has 5 axis g-code please give me

10

General Mach Discussion / Re: i have a problem with rhino cam 2.0 5 axis.

« on: April 27, 2012, 06:50:31 AM »

thank hood