Hello Guest it is March 28, 2024, 06:05:20 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - DaveCVI

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 »
111
Finished Plugins for Download / Re: Huanyang VFD controller plugin
« on: February 23, 2011, 03:03:57 AM »
Hi,
I'm the author of MachStdMill (MSM) - here's some info:
MSM uses DRO 39 as does the 1024 screen set - that is the DRO mach updates with the true spindle RPM.
DRO 39 is updated by Mach - neither MSM nor 1024 have a hand in determining the DRO value. it's just on a page and mach updates it's value as mach does all the other DROs.

With the plug-in my impression is that the RPM data comes from the VFD and the plug-in then displays it in a user DRO (at least that's what the plug-in manual seems to imply to me).

Does the author of the Plug-in hang around here?
I'd be happy to talk with him as to what his plug-in is doing etc.
If the plug-in will route the RPM data from the VFD to DRO 39, then I'd think all would be well.

Dave

I don't know much about Mach3 (new user) but afaik the adress for Spindle RPM is 39? I have used the screen editor to look at the # and both the 1024 and machstdmill screens have the same # (39). Is that what I should put in the plugin??

Best regards /L

112
General Mach Discussion / Re: Spindle pulley setup?
« on: February 16, 2011, 05:55:06 PM »
You can change the currently selected pulley by changing the Spindle pulley DRO - in the stock 1024 screen set that DRO is on the diagnostics page. That avoids the need to go into the mach menus to change the selected pulley.
Dave

If I tick the reverse in the box it does reverse, I just want to know if I have to go into the config, spindle pulleys screen every time to change it from #1 to #2?
Ray.

113
VB and the development of wizards / Re: VB and modIO + macropump.ms1
« on: February 16, 2011, 03:51:38 PM »
FYI -
It is possible to have more than one "macropump" - i.e. multiple scripts that are run periodically.
They can also all have different run periods. They disk file names of the scripts will not all be called "macropump.m1s".

I make use of this ability in MSM (MachStdMill).

The ability to do this is fairly recent and few people seem to have figured out that this is possible in current version of mach - this is why when searching past posts you won't find a lot of references to this ability.

Get the Mach programmers from http://machsupport.com/docs/Mach3_V3.x_Macro_Prog_Ref.pdf and look at
StartPeriodicScript and StopPeriodicScript

Dave

114
General Mach Discussion / Re: Spindle pulley setup?
« on: February 15, 2011, 11:58:51 PM »
Hi,
FYI - apparently the pulley reverse is broken in 3.43.22 (current lock down).
There was a bug in the spindle pulley reverse stuff that has been the subject of a thread on the Yahoo Mach list for the last couple of days. A new development version was just released today that is supposed to fix it (3.43.30).

Dave

115
Mach Screens / Re: MachStdMill Screen CV and ES button
« on: February 09, 2011, 04:57:03 PM »
Jeff,
What version of MSM are you using?
I just checked and with the current version of MSM G61 gives ES and G64 gives CV and the two buttons/LEDs are not swapped.

BTW - I just happened to see your post here - the best place to get MSM questions answers is www.calypsoventures.proboards.com

Dave



On the run screen, when I use exact stop in my program (G61) it's the CV button that is highlighted and when I use G64 for constant feed, that's the ES button that is highlighted.

I need to use both G64 and G61 in my program.

The code are accepted . The machine runs fine, just button that are inverted.

Jeff

116
CVI MachStdMill (MSM) / Re: Announcement: MachStdMill (MSM) Released
« on: January 25, 2011, 01:49:24 PM »
Hi,
Just a reminder: the MSM introduction special pricing will expire in less than a week - at the end of the month (1/31)
Dave

117
General Mach Discussion / Re: Announcement: MachStdMill (MSM) Released
« on: January 25, 2011, 01:47:26 PM »
Hi,
Just wanted to remind folks that the MachStdMill introduction pricing specials will expire at the end of the month (on 1/31).

Dave



118
Finished Screens / Announcement: MachStdMill (MSM) Released
« on: January 13, 2011, 06:31:44 PM »
Hi,
MachStdMill is a professionally designed and extensively tested enhancement package (often referred to by it’s initials “MSM”) for Mach3. MSM is now available to Mach3 users from Calypso Ventures, Inc (CVI). 

For more information, please visit our web site at: www.CalypsoVentures.com where you can learn about the features included in MSM.

Free, fully functional trial versions of MSM are available for download.

The CVI web site has MSM feature descriptions, pricing, edition comparisons, and the full user manual and release notes are available for download. The MSM user community forum is also online and may be accessed via the CVI site support page.

After a 6 month beta test program involving many users and thousands of downloaded beta copies, MachStdMill successfully met all the beta test exit criteria and was approved for product release.  MSM is probably the most extensively tested add-on package available for Mach3 and we’re pleased to note that there are no unresolved bugs known in the MSM product release.

In recognition of the world wide nature of the Mach3 user base, software licenses may be purchased online 24/7 using a major credit card.

Finally, as part of the MSM product introduction, special product introductory pricing is available (just use the priority code provided on the CVI  software store page during checkout).

Dave

119
General Mach Discussion / Announcement: MachStdMill (MSM) Released
« on: January 13, 2011, 06:28:15 PM »
Hi,
MachStdMill is a professionally designed and extensively tested enhancement package (often referred to by it’s initials “MSM”) for Mach3. MSM is now available to Mach3 users from Calypso Ventures, Inc (CVI). 

For more information, please visit our web site at: www.CalypsoVentures.com

Free, fully functional trial versions of MSM are available for download.

The CVI web site has MSM feature descriptions, pricing, edition comparisons, and the full user manual and release notes are available for download. The MSM user community forum is also online and may be accessed via the CVI site support page.

After a 6 month beta test program involving many users and thousands of downloaded beta copies, MachStdMill successfully met all the beta test exit criteria and was approved for product release.  MSM is probably the most extensively tested add-on package available for Mach3 and we’re pleased to note that there are no unresolved bugs known in the MSM product release.

In recognition of the world wide nature of the Mach3 user base, software licenses may be purchased online 24/7 using a major credit card.

Finally, as part of the MSM product introduction, special product introductory pricing is available (just use the priority code provided on the CVI  software store page during checkout).

Dave


120
General Mach Discussion / Announcement: MachStdMill (MSM) Released
« on: January 13, 2011, 06:27:19 PM »
MachStdMill is a professionally designed and extensively tested enhancement package (often referred to by it’s initials “MSM”) for Mach3. MSM is now available to Mach3 users from Calypso Ventures, Inc (CVI). 

For more information, please visit our web site at: www.CalypsoVentures.com

Free, fully functional trial versions of MSM are available for download.

The CVI web site has MSM feature descriptions, pricing, edition comparisons, and the full user manual and release notes are available for download. The MSM user community forum is also online and may be accessed via the CVI site support page.

After a 6 month beta test program involving many users and thousands of downloaded beta copies, MachStdMill successfully met all the beta test exit criteria and was approved for product release.  MSM is probably the most extensively tested add-on package available for Mach3 and we’re pleased to note that there are no unresolved bugs known in the MSM product release.

In recognition of the world wide nature of the Mach3 user base, software licenses may be purchased online 24/7 using a major credit card.

Finally, as part of the MSM product introduction, special product introductory pricing is available (just use the priority code provided on the CVI  software store page during checkout).

Dave


Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 »