Hello Guest it is May 15, 2021, 08:24:52 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - maestro123

Pages: 1
1
General Mach Discussion / Re: help with DC DC converter
« on: June 28, 2010, 06:43:07 PM »
Thanks Tweakie...

2
General Mach Discussion / Re: help with DC DC converter
« on: June 26, 2010, 05:08:57 AM »
No Tweakie for the moment i have not noise.

One time it happened that X axis made unexpected movement..!!

The manufacturer said that this system is designed to keep very low noise, so i think that is professional to have "AFC5".


3
General Mach Discussion / Re: help with DC DC converter
« on: June 25, 2010, 05:32:34 PM »
hi tweakie,

it's destinate to decrease noise and i have taked it from a professional cnc machine


4
General Mach Discussion / help with DC DC converter
« on: June 25, 2010, 11:24:11 AM »
hi,

I am fortunate to have a dc dc converter  :D to minimize the noise in the system

but I did not find how to connect ???

here is the datasheet of the  main element "AFC5"

 is that someone can help me to connect

thank you in advance


5
General Mach Discussion / Re: Nothing is moving...
« on: June 21, 2010, 01:32:03 PM »
sorry for delay...
 hi,
tweakie i resolved the problem:
 - first i bought i new pci printer card and it carrie  5v or 0v i jogging
 - second some integrated circuit "SN74LS00" was broken so i changed and the motor finally move...

thanks for help and suggestion

6
General Mach Discussion / Re: Nothing is moving...
« on: June 02, 2010, 01:18:52 PM »
I had yet downloaded parmon and all seems fine and when i try jogging motor pins change color from green to red and from red to green but there is something unusual when i used a multimiter to know parallele port voltage and it show :
pin 2 and pin 3 = 4.39v when i jog X+ and  1.86 with X-
pin 4 and pin 5 = 2.89v when i jog Y+ and  0.75 with Y-
pin 6 and pin 7 = 1.60v when i jog Z+ and  0.60 with Z-

pin 3 and pin 10 =4.40v
pin 5 and pin 10 =4.40v
pin 7 and pin 10 =4.40v

is that seems normal..!

7
General Mach Discussion / Re: Nothing is moving...
« on: June 02, 2010, 09:08:36 AM »
and i had wired the stepper in this way :

8
General Mach Discussion / Re: Nothing is moving...
« on: June 02, 2010, 07:36:52 AM »
yes Tweakie and that what i have as chown in the picture

9
General Mach Discussion / Nothing is moving...
« on: June 02, 2010, 05:33:50 AM »
hi,

I 'm newest in CNC and i have some problem : motors don't move :-\

I am setting up a 3 Axis system and am using a package from Kelinginc.net which is

5056 drivers using a C10 breakout board.


On the C10 board, I have jumpers set as follows :

__Pins 2 - 9 jumpered for output

__Pins 2 - 9 jumpered for pull down

__com jumpered for com=5V

__input pins 10 - 15 jumpered for pull down

-Pin 2 = x step  -pin 3 = x dir
-pin 4 = y step  -pin 5 = y dir
-pin 6 = z step  -pin 7 = z dir


there are no limit/home switches connected.
there is an Estop switched to Pin 10



thanks for help...

Pages: 1