Messages

11

General Mach Discussion / Re: Smoothness EXTREME need of help

« on: November 13, 2009, 04:46:43 PM »

wow!

That did it.

I cant believe that all i had to do was increase the CV rate.

What does CV stand for and what does it do?


Thank you very much.

12

General Mach Discussion / Re: Smoothness EXTREME need of help

« on: November 13, 2009, 04:41:53 PM »

how do i change the cv feedrate?

13

General Mach Discussion / Re: Smoothness EXTREME need of help

« on: November 13, 2009, 03:39:24 PM »

CV feedrate = +1

14

General Mach Discussion / Re: Smoothness EXTREME need of help

« on: November 13, 2009, 02:45:37 PM »

CAn someone give me an example of code generated from polylines.

Please.

thanks,

-Bryson

15

General Mach Discussion / Re: Smoothness EXTREME need of help

« on: November 13, 2009, 01:43:19 PM »

how do i create polylines?

16

General Mach Discussion / Re: Smoothness EXTREME need of help

« on: November 12, 2009, 07:32:23 PM »

I added the G64 with no avail.  I think that our machine is a piece and is not capable of making round turns without stopping.

17

General Mach Discussion / Re: Smoothness EXTREME need of help

« on: November 12, 2009, 07:09:21 PM »

O1111 (DOES 1 COMPLETE 1 FT FIXTURE)
( W .020 RTV THICKNESS)
(X0 CENTERED ON LEFT RAIL OF FIXT.1)
(Y0 AT EDGE OF PART)
(Z0 AT HIGHEST POINT OF FIXTURE)
(DC 732 AT 45PSI,GREEN PLASTIC TIP)
(5-15-09 REV.= )
G0 G90 G17 G40 G54
(DISPENSING)
G0 X-7.0 Y3.0 Z.5
M00 (VERIFY DISPENSE)
G0 X-.0858 Y-.5
G0 Z0
G01 Z-.26 F20.0 (SET NEEDLE HEIGHT FOR 1)
M00
M98 P17
G90 G0 Z.5
X-7.0 Y3.0
M00 (WIPE TIP OF DISPENSER)
Y24.0(INSTALL GLASS)
M30
%

O17
G0 G91 G17 G40 G54
G01 Y12.18 F180
X.155 Y.155 r .175 F300
G01 X1.48 F180
G17 G02 Y-.155 X.155 r .175 F300
G01 Y-11.50 F180
G17 G02 X-.155 Y-.155 r .175 F300
G01 X-1.48 F180
G17 G02 X-.155 Y.155 r .175 F300
G4P0
G01 Z -.02
G01 X.1
G01 X-.1
G01 X.1
M99
%

18

General Mach Discussion / Re: Smoothness EXTREME need of help

« on: November 12, 2009, 06:53:16 PM »

It was set at 20.  I changed it 50 and then 1 and then 20 again and no difference.

 

19

General Mach Discussion / Re: Smoothness EXTREME need of help

« on: November 12, 2009, 06:41:37 PM »

what does the look ahead command do?

20

General Mach Discussion / Re: Smoothness EXTREME need of help

« on: November 12, 2009, 06:30:13 PM »

Even with those mods in the G-code, the machine still does the same thing.  It follows the straight line at first, pauses for fraction of a second, then proceeds to make the arc and pauses again before making the horizontal line.

After the glue is dispensed, my rectangle is created with little piles of excess glue in the corners.

What can i DO?