Hello Guest it is January 26, 2022, 06:04:23 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - peter81

Pages: « 1 2 3 4 5 6 7 8 9 10 11 »
71
General Mach Discussion / Re: Grease pump
« on: February 21, 2011, 03:45:03 PM »
Here is the manual of the servos. I'm also using DSPMC/IP controller. Thanks.

Peter

72
General Mach Discussion / Re: Grease pump
« on: February 21, 2011, 02:43:13 PM »
Hi, yes that could also be possibility but in my case not because I don't have any output shaft to mount the encoder or black wheel. I use servos and rack and pinion drive and there is just 2mm of space between pinion and table. Thanks again for the idea.

Peter

73
General Mach Discussion / Re: Grease pump
« on: February 21, 2011, 05:05:20 AM »
Thanks Hood I will take a look.

Peter

74
General Mach Discussion / Re: Grease pump
« on: February 20, 2011, 06:07:36 PM »
Hi,
yes that would also be worth considering. Can you please tell me how to do it? Thanks.

Peter

75
General Mach Discussion / Re: Grease pump
« on: February 20, 2011, 02:04:53 PM »
How do you propose to measure the distance of travel? How does the 50m accumulate? If the machine does a 1m rapid and then 11 back-and-forth 100mm moves, does the total equal 1.1m or 2.1m?

I think the total distance should be 2.1m. The rapid moves should also be counted.

76
General Mach Discussion / Grease pump
« on: February 20, 2011, 09:22:08 AM »
I need some help with my auto lubricate system to set it up in mach3. I will need a output to go on and off for a specific set of time on every 50 meters of travel to activate my grease pump system. Is there a way to do it in brains and how. Thanks.

Peter

77
dspMC/IP Motion Controller / Re: Pokeys and MPG
« on: February 04, 2011, 12:52:16 PM »
Ok thanks Rufi. This means that I will have to replace usb cable from the pendant. Thanks.

Peter

78
dspMC/IP Motion Controller / Re: Pokeys and MPG
« on: February 02, 2011, 12:49:33 PM »
Has anyone succcessfuly connected mpg trough pokeys to use with dspmc? Is that possible or do I need to wire it to a hardware encoder input?

Peter

79
dspMC/IP Motion Controller / Re: Pokeys and MPG
« on: January 26, 2011, 09:22:45 AM »
When I connect my pendant to a laptop at my home, MPG works ok and I can see the DRO counts, but when I try to run on my cnc computer I can't get any movement. I get message in status line: Already in joging mode! Can someone please tell me what should I do to make it work. Thanks.

Peter

80
dspMC/IP Motion Controller / Pokeys and MPG
« on: January 25, 2011, 12:21:24 PM »
Hello,

can somebody please help me with my home made pendant. I'm using pokeys and I have connected Mpg to input pins 1 and 2. All of the functions are working (LCD, start, stop, pause, axis selector, x1, x10, x100) except MPG. In mach3 settings page I can see MPG counts but axis dont move. What could be the problem?


Pages: « 1 2 3 4 5 6 7 8 9 10 11 »