Hello Guest it is December 02, 2022, 12:09:14 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - willems

Pages: 1 2 »
1
General Mach Discussion / Re: incorrect dimensions when inverting x axis
« on: September 23, 2010, 03:35:44 AM »
many thanks hood
yes the incorrect dimentions came from the same .dxf file but when changing X axis the milling changed from conventional to climb or vice versa
we got a difference of 2x 0.5mm = 1mm in multiplex (wood)
so we have to master the milling direction for critical figures. You know an easy way ????
a.willems

2
General Mach Discussion / Re: incorrect dimensions when inverting x axis
« on: September 21, 2010, 05:07:34 AM »
what is your best way to go from .DXF files to G code?
'specify climb or conventional milling' ?????
a.willems

3
General Mach Discussion / Re: incorrect dimensions when inverting x axis
« on: September 17, 2010, 04:11:44 AM »
good day hood,
there is nothing wrong...nor the machine nor any program
the only change while milling circles after changing X axis is that they are made counterclockwise in stead of clockwise
so with a rather dull milling tool in wood we got incorrect dimensions
we will try to ask lazycam to program the circles counterclockwise to verify (you know is is possible?)

thanks again
a.willems

4
General Mach Discussion / Re: incorrect dimensions when inverting x axis
« on: September 15, 2010, 04:18:10 AM »
we cloned the good file and changed te X axis homing direction
and have THE SAME PROBLEM......
the only thing we changed was in homing and limits...
same files, same program, same machine...
can somebody try this on his machine?
thanks in advance
a.willems

5
General Mach Discussion / Re: incorrect dimensions when inverting x axis
« on: September 15, 2010, 03:59:07 AM »
good day again hood
we used your file, no problems with the milling, but the incorrect dimensions are still there....
we have the same missing 1mm on all circles of the test file we send you in G code
we will clone the good XML and try again
until later
a.willems

6
General Mach Discussion / Re: incorrect dimensions when inverting x axis
« on: September 14, 2010, 06:17:07 PM »
the one above with 'rechts' in te name was the wrong one
lets wait and see
thank you very much for the help
until tomorrow
a.willems

7
General Mach Discussion / Re: incorrect dimensions when inverting x axis
« on: September 14, 2010, 06:12:46 PM »
thanks,
file is alreay downloaded
we will try it in a few hours (machine is now running) and we will give you the results.
Can, you say wath you did in the file?  so , if good working, we can prevent for the future?

until tomorrow
a.willems

8
General Mach Discussion / Re: incorrect dimensions when inverting x axis
« on: September 14, 2010, 06:03:52 PM »
we do not use a tool of 0.5mm
we use only a tool of  4 mm
to get a drill of (nearly) 4mm we use in autocad (via DXF and lazycam) a circle of 0,5mm
a.willems

9
General Mach Discussion / Re: incorrect dimensions when inverting x axis
« on: September 14, 2010, 05:58:10 PM »
the good one with correct dims is the XML file with 'LINKS' in its name
a.willems

10
General Mach Discussion / Re: incorrect dimensions when inverting x axis
« on: September 14, 2010, 05:53:32 PM »
About the DRO's, we did not verify yet
YES we have the same problems with a square cut to
it seems more like an unwanted 'cutter radius compensation' because we have always the same faulty distance
in litlle or large figures
is there a way to really force the G40 command?
in attach a test G code we used to define the faulty dim's
thanks in advance
a.willems (belgium at five to midnight )

Pages: 1 2 »