Hello Guest it is March 29, 2024, 10:06:16 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Mauri

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 »
171
Mach4 Videos / Re: MACH4 HICON INTEGRA
« on: September 04, 2017, 06:50:37 PM »
ikigam,
yes.
Regards,
Mauri.

172
gadman58,
I tested the 3481 Plugin and it or mach4 3481 has an issue it stops during a cutting run.
Vital Systems were testing as well.
Plugin 3481 is not released yet and you cannot use OLDer HiCON plugins on new Mach4 (3481) releases.
Regards,
Mauri.

173
Mach4 Videos / Re: MACH4 HICON INTEGRA
« on: September 04, 2017, 05:00:08 PM »
ikigam,
You should post your question on the HiCON Forum
http://www.machsupport.com/forum/index.php/board,89.0.html
This will ensure Vital Systems can read it an assist you.
You need to setup Mach4 Config on the Motors and also see if the HiCON Plugin Config is setup correctly.
There are other Plasma users on the HiCON forum page.
Regards,
Mauri.

174
Mach4 General Discussion / Re: Mach4 Axis Calibration...
« on: August 24, 2017, 11:48:29 PM »
Hi,
There is a Wizard in Mach4 "StepPerUnitCalculatorBasic".
Regards,
Mauri

175
Mach4 General Discussion / Re: Where did 3468 and 3474 go to
« on: August 14, 2017, 04:21:13 PM »
Stuart,
3468 and 3474 have been removed to add more detailed Error messages in case if crashes.
Most likely 3474 will be released soon into production.
I had 3468 stop near the end of a +3Hrs process with an ambiguous error message, in comparison 3390 was/is unbreakable.
Regards,
Mauri.

176
rcaffin,
Not sure how it is trying to display the G-Code in the Mach4 Toolpath.
When you rotate the object in the Toolpath it keeps its unrecognizable form.
On a perfect circle if you offset the circle in you CAD program by 50% then make the G-Code and load it into Mach4, it will display correctly, but if you cut it, it will be 50% offset.
On other objects like a  3D Bust or Statue if you Rotate it or not, the Toolpath display shows no resemblance to the object and does not show the object fully formed, it shows it squashed in.
All versions of Mach4 for the last 2.5years have been the same.
Regards,
Mauri.

177
Hi,
The problem is with my new Plugin.
Thanks,
Mauri.

178
Hi,
I am trying to test Mach4 V3468 however it will not show my Controller Plugin and will remove all my settings in the Input and Output Signals.
Does anyone else have this issue, if not what could I be doing wrong?
I can see the new plugin in the directory, however it can not be seen or added by this version of Mach4.
Any assistance would be appreciated.
Regards,
Mauri.

179
Cbyrdtopper,
Yes that is the issues I have.
On all my 3D statues or even a simple circle it bears no resemblance to the objects to be machined.
The G-Code statues is just an odd unrecognizable shape and the G-Code circle is just a straight line.
So this issue is just not me good to know.
It is difficult to proceed when you are not sure Mach4 will machine it correctly and you cannot view in the Toolpath G-Code to see if it is how you want it machined.
Regards,
Mauri.

180
Cbyrdtopper,
Just a question can you display your machining G-Code "Toolpath's" for your cutting tool machining in Mach4 and do they display correctly?
Regards,
Mauri.

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 »