Messages

11

Mach SDK plugin questions and answers. / Re: Impact engraving plugin

« on: March 24, 2011, 08:45:58 AM »

Hello, I am working right now 20000mm/min with good results, but I want to modify the machine for more speed, removing weight to the head, I'm talking laser.
Pulse then has nothing to do with speed? pulse is associated to the image
More speed to shoot faster pulse?

As able to analyze the signal correctly?
A completely white tendira pulse rate?

Best regards

12

Mach SDK plugin questions and answers. / Re: Impact engraving plugin

« on: March 24, 2011, 06:04:31 AM »

good morning,
 I'm making a machine to work at high speed.
 While this plugin will respond at speeds of 50 m / min or 100m/min?
 Pulse rate varied by varying the speed of work?

 best regards

13

Mach SDK plugin questions and answers. / Re: Impact engraving plugin

« on: February 16, 2011, 12:04:55 PM »

And I tried it and it goes well, I see strange is that when I very low speed (30cm/min) will not turn on the laser. "Should be activated at any speed?

14

Mach SDK plugin questions and answers. / Re: Impact engraving plugin

« on: February 16, 2011, 10:39:58 AM »

hello

His work is perfect.

Could send me a screen the configuration of the motor tuning? to get for an example

Thank you very mach

15

Mach SDK plugin questions and answers. / Re: Impact engraving plugin

« on: February 16, 2011, 08:12:05 AM »

hello

I used this plugin with a laser, pin1 connecting the port directly to the power supply of the laser (ttl)

but unless I activate the laser speed with less power more speed work to more power is the laser

to 3m/min. not turn on the laser, and 20m/min. the laser work perfect whit your power.

why is it so?
MACH3'll have the bad configuration?

thank you very mach

16

Mach SDK plugin questions and answers. / Re: Impact engraving plugin

« on: January 18, 2011, 03:06:23 AM »

Hello,
Where I can buy stepper board? In Ebay?

Thank you

17

Mach SDK plugin questions and answers. / Re: Impact engraving plugin

« on: January 13, 2011, 06:00:36 AM »

Stitos,

Having tried with a portable oscilloscope, it is obvious that a much more fancy digital, recording piece of equipment will be necessary here.
All I have been able to confirm, so far, is that the pulse width is indeed 40uS and the Pulse Repetition Frequency at white is 0% increasing with shade to approx 90% at black but I have been unable to accurately measure the gap (pause) between the edges (join) of each pixel in the image but this does vary with feedrate.
Not much help really but I will try with another scope when time permits.

Tweakie.

OK, thank you very much

18

Mach SDK plugin questions and answers. / Re: Impact engraving plugin

« on: January 11, 2011, 04:51:04 AM »

Thank you very much. Can in difernt feedrate and image total white. And image total black.

I don´t have oscilloscope.

Thank you very much

19

Mach SDK plugin questions and answers. / Re: Impact engraving plugin

« on: January 11, 2011, 03:27:57 AM »

sorry for the translation

The pulse is 40us on? and 40us pulse is off? continuously.
In the imge white, for example
is 12500Hz the frecuency?

20

Mach SDK plugin questions and answers. / Re: Impact engraving plugin

« on: January 10, 2011, 07:59:52 AM »

The plugin work in zone white, lanch 40us (On) and 40us(Off) repit it frecuency etc......
The frecuency of work is 125Hz