Hello Guest it is April 26, 2024, 03:26:14 PM
Profile Guest

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Chris.Botha

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 »
351
Show"N"Tell ( What you have made with your CNC machine.) / Re: Gertrude Gets Some!
« on: May 24, 2009, 02:14:32 AM »
and this is what you look like after too much milling....


352
Show"N"Tell ( What you have made with your CNC machine.) / Re: Gertrude Gets Some!
« on: May 24, 2009, 02:03:26 AM »
this one also with 0.076mm cutter


fresh of the mill.. man busy Sunday... time for a beer and a bbq!


353
Show"N"Tell ( What you have made with your CNC machine.) / Re: Gertrude Gets Some!
« on: May 24, 2009, 01:46:51 AM »
think they go down as far as 0.001thal or 0.025mm

354
Show"N"Tell ( What you have made with your CNC machine.) / Re: Gertrude Gets Some!
« on: May 24, 2009, 01:45:24 AM »
lol yeah i think you yanks call it a 0.003thal cutter

http://www.bitsbits.net/index.php?main_page=product_info&cPath=17&products_id=19

:)



355
Show"N"Tell ( What you have made with your CNC machine.) / Re: Gertrude Gets Some!
« on: May 24, 2009, 12:36:45 AM »
this is better.. texture more apparent and generally crisper.. went down to 0.076mm cutter


356
Show"N"Tell ( What you have made with your CNC machine.) / Re: Gertrude Gets Some!
« on: May 23, 2009, 11:43:08 PM »
first attempt at head was a failure!

bad designing..


back to the drawing board...

357
Show"N"Tell ( What you have made with your CNC machine.) / Re: Gertrude Gets Some!
« on: May 23, 2009, 10:33:24 PM »
step one done, head on mill now.

358
Show"N"Tell ( What you have made with your CNC machine.) / Re: Gertrude Gets Some!
« on: May 23, 2009, 10:32:45 PM »
have to knock off this ring.. bigger, thicker etc..


359
Show"N"Tell ( What you have made with your CNC machine.) / Re: Gertrude Gets Some!
« on: May 23, 2009, 04:35:02 AM »
more signet action.. havea  few other pieces to mill for this COA's


360
Show"N"Tell ( What you have made with your CNC machine.) / Re: Gertrude Gets Some!
« on: May 22, 2009, 05:03:15 PM »
hehehe .. yeah ok i do..

did i say 30 micron. my bad i meant 300 micron.. look at thickness of wire on falr left and far right on top picture to see whaqt i mean grrrrrrrrrrrrrrrr

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40 41 42 43 44 45 46 47 48 49 »