Hello Guest it is March 28, 2024, 05:44:34 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - jve

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 »
31
General Mach Discussion / Re: csmio
« on: June 29, 2013, 07:04:06 AM »
I post the code may be I have something missing here

32
General Mach Discussion / Re: csmio
« on: June 29, 2013, 07:00:01 AM »
I made that enabled but it keep making same think no luck !!!

33
General Mach Discussion / Re: csmio
« on: June 29, 2013, 06:31:23 AM »
I made a copy of machine vb,xml may be you can help be a bit more  :)

34
General Mach Discussion / Re: csmio
« on: June 29, 2013, 06:11:36 AM »
first of all it is not working like the vid and the problem is the machine is making the first pass then it has to pull out from the tread and it is taking very long with a feed rate of 1.5mm and after that it goes out to make the second tread with rapid and it makes the second tread and again it is making same thing goes slow out of the tread and the it goes with rapid to continue the tread and it keep doing this all the tread passes also on every start of a tread the spindle slows down
I do not know what im doing wrong
can I ask you which firmware are you using on the csmio?

35
General Mach Discussion / Re: csmio
« on: June 29, 2013, 05:30:44 AM »
now I am running on 057 and the tread is cutting in air and I don't believe that the spindle will slow down by force with a 24kw spindle motor
I think I did not explain my self good on the above when it makes the first pass and it is going to pull out from the tread it is taking a while like 50sec this means that it is with a feed rate of 1.5mm and not with rapid

36
General Mach Discussion / Re: csmio
« on: June 29, 2013, 05:06:44 AM »
I notice also that on each pass of the tread the spindle slow down does this happen to you also ?
so it should be an update of mach3
do you know anything with mach4 and csmio if they going to work with each other?

37
General Mach Discussion / Re: csmio
« on: June 29, 2013, 01:37:54 AM »
ok hood it worked when I invert the encoder but I still have an other problem with the treading as of now I am making a tread internal and when it makes the first cut it pull out with a feed of 1.5mm it should not work like that it should pull out with rapid movement and it keep repeating 2nd ,3rd ecc
I am doing the tread by the G76
G76 X-54 Z-22 Q0 P1.5 J0.2 L0 H0.2 I30 C1 T0
this program it use to work with mach3 and with the parallel port it is something with the csmio I think is there any setting that I am missing ?

38
General Mach Discussion / Re: csmio
« on: June 28, 2013, 12:47:03 PM »
I found  an other problem I tried a program in the air (without stock) and when it came for treading it went to reset but I am using the G76 as a treading cycle does it work with the csmio ?

39
General Mach Discussion / Re: csmio
« on: June 28, 2013, 10:38:39 AM »
yes it is 66 what is the best one?

40
General Mach Discussion / Re: csmio
« on: June 28, 2013, 07:38:52 AM »
I notice that when I input code t606m6 the work coordinates come ok but when I input code t616m6 the work coordinates come the same as t606m6 then if I input again t616m6 the work coordinates change the value as it should be so I have to input t616m6 2 times is there any setting that im missing?

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 »