Hello Guest it is March 28, 2024, 05:21:13 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Topics - jve

Pages: 1 2 3 »
1
VB and the development of wizards / auto soft limits
« on: December 26, 2018, 10:36:54 AM »
Hi Every one ,

I would like to set mach3 to set the soft limit button automatically after reference but when the machine is not referenced the soft limit led will go off ,  anyone has a ready script?

2
VB and the development of wizards / ATC Geneva wheel for mill
« on: April 04, 2018, 11:19:19 AM »
HI Guys,

I need some help, I am doing a retrofit in a mill that have a ATC with a geneva wheel
It  is working fine with the inputs and output the problem that i have is the count and i cannot figerout what is the problem
when the ATC is in tool1 for example and i insert T2M6 the ATC go to tool 2 but when the ATC is in tool 1 and i insert T3M6 it go to tool 2 so it is only counting 1



3
General Mach Discussion / spindle problem
« on: March 25, 2015, 01:55:16 PM »
hi all,

i been using mach 3 for several times and today i tried to make a spindle working 0 to 10v with a csmio controller i manage to make it working with no problems it is varying but this is the most strange thing that i have when you type in the mdi m3 s1000 the spindle starts and it will run 1000 but if i type 2000 the spindle will keep 1000 then when i press reset spindle over ride it will go 2000 so basically i have to press the reset spindle override to ghange the spindle speed after i type in mdi or in g code  file 
do i am missing something ????????

4
General Mach Discussion / atc macro
« on: August 12, 2014, 06:30:05 AM »
hi all,

i am sure that some of been pass this before i need a macro for a atc which has 10tools along the y axis not with pocket it has to slide in with the x axis anyone has something ready and i will modify 

5
General Mach Discussion / csmio
« on: June 21, 2013, 12:19:19 PM »
hi guys
i been using csmio ips for a few machines now but these machines i never needed the analog out put before and this time i am making a retrofit on a big lathe my problem is that i enabled the analog output from the plugin and i setup the spindle pulley there is no output voltage there even when i go to check on the plugin the bar for the analog output 0 it remains 0 so there is no output to the spindle drive
do i am missing something?

6
General Mach Discussion / g31
« on: June 22, 2012, 08:46:51 AM »
is it possible mach3 trigger an output when i have a g31 and when g31 is ready the output will go off

7
General Mach Discussion / vb for g31
« on: June 21, 2012, 02:07:48 AM »
hi guys
i am trying to make a vb but no luck what i want to do is when i have a G31 in my code i need to activate a output and when it is ready deactivate the output is this possiple
regards
jekran

8
General Mach Discussion / g31 output
« on: April 16, 2012, 01:47:22 PM »
hi guys
i need to activate an out put when i call G31 or G28.1 in the g code program is this posible ?
regards
j

9
General Mach Discussion / rapid rate
« on: April 01, 2012, 05:20:23 AM »
hi guys
i have my mill which it use to have an analog potentiometer that it will regulate the rapid rate and the feed rate instant which mach3 is not making i want to ask if this is possible with mach3 cause for setting up a new job this is very usefull the problem is that mach3 is looking forward the code and when i close the rapid rate it will take a while before it will come active also on the config page there is a box (look forward gcode) and mine is set 20lines if i set this to 0 lines does this come to instant active when i close the rapid rate to 0%

10
General Mach Discussion / analog to thc
« on: October 10, 2011, 05:32:27 AM »
hi guys
i am thinking to have a ultrasonic or a laser sensor that can give me a 0 to 10v analog signal and then mach3 will converted to torch up and torch down is this possible to do via brains ?
regards
jekran

Pages: 1 2 3 »