Hello Guest it is March 28, 2024, 07:28:44 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - cor

Pages: « 1 2 3
21
LazyCam (Beta) / Re: unable to post more as ca 10 chains
« on: March 02, 2009, 02:50:18 PM »
hey,

I am a step further right now :-).... but not far enough :-/

I have loaded your tap file in mach3 and it showed all lines. I have opened both my tap file and your tap file (in notepad), and mine stops at line 250 (probably drawing  line #9) and yours continue to line 635 to do the other lines.

So , I now know it is not mach3 whioch is playing up, but something in lazycam.

What I did is:
loaded this dxf file and pressed the "post code" button, that's all. Maybe lazycam needs some more finetuning? , but where?, not many option to change? ???

I upload my tap file as well, so you can see the difference.

Where can I start looking in lazycam where the "error" is?

I really do appriciate your help.

regards,
cor

22
LazyCam (Beta) / Re: unable to post more as ca 10 chains
« on: March 02, 2009, 06:42:30 AM »
Hello Chip,

attached the dxf file, maybe you can take a look at it.

The 50 lines would allready be the answer I think, I thought it was 500 lines.

Best regards,
Cor

23
LazyCam (Beta) / unable to post more as ca 10 chains
« on: February 28, 2009, 02:57:26 PM »
Hello there,

I am quite new to all this cnc , mach3 lazycam stuff, but slowly I am getting there.

For testing my homebuild cnc router I made in rhinoceros 15 vertical lines and 15 horizontal lines. Exported to dxf and opened it in lazycam.
lazycam show these lines perfectly.
When I post them in Gcode and open it in Mach3 only the horizontal lines are displayed. When I move some vertical "chains" more up and then post, these vertical lines show up, but not all of them and than I am missing some horizontal lines again :-/

The same when I make a lot of objects like cirkels, squares , lines etc not all of them are posted in gcode, but are shown in lazycam as seperate chains.

Here some pictures:
The lines in Rhinoceros:

Saved as dxf file
opened in lazycam (mill):


All lookes fine, pressed the "post gcode"button"

Only 9 lines are displayed  ???

here the g-code:

------------------------------------------------------------
N1 (File Name = 200 on Sunday, March 01, 2009)
N2 (Default Mill Post)
N3  G91.1
N4 G0  Z1.0000
N5 M3
N6  X150.0000  Y1.0000
N7  Z0.1000
N8 G1  Z0.0000  F60.00
N9  X0.0000   
N10 G0  Z1.0000
N11  X150.0000  Y5.0000
N12  Z0.1000
N13 G1  Z0.0000 
N14  X0.0000   
N15 G0  Z1.0000
N16  X150.0000  Y9.0000
N17  Z0.1000
N18 G1  Z0.0000 
N19  X0.0000   
N20 G0  Z1.0000
N21  X150.0000  Y13.0000
N22  Z0.1000
N23 G1  Z0.0000 
N24  X0.0000   
N25 G0  Z1.0000
N26  X150.0000  Y17.0000
N27  Z0.1000
N28 G1  Z0.0000 
N29  X0.0000   
N30 G0  Z1.0000
N31  X150.0000  Y21.0000
N32  Z0.1000
N33 G1  Z0.0000 
N34  X0.0000   
N35 G0  Z1.0000
N36  X150.0000  Y25.0000
N37  Z0.1000
N38 G1  Z0.0000 
N39  X0.0000   
N40 G0  Z1.0000
N41  X150.0000  Y29.0000
N42  Z0.1000
N43 G1  Z0.0000 
N44  X0.0000   
N45 G0  Z1.0000
N46  X150.0000  Y33.0000
N47  Z0.1000
N48 G1  Z0.0000 
N49  X0.0000   
N50 G0  Z1.0000

-----------------------------------------------------------------



What am I doiing wrong  ???

many thanks,
cor

Pages: « 1 2 3