Messages

11

Bargain Basement / Re: X2 Minimill cnc'd

« on: June 07, 2016, 02:51:32 PM »

Here's the other

12

Bargain Basement / Re: X2 Minimill cnc'd

« on: June 07, 2016, 02:48:58 PM »

Hi All,
Had some time to go through the extra parts that come with the mill and have attached a couple of photo's for look's.... Hope they come out so you's can see ..

                                  Thanks ; H S.

13

Bargain Basement / Re: X2 Minimill cnc'd

« on: April 21, 2016, 03:25:34 PM »

Hi All,
Just needed to BUMP this thread..

14

Bargain Basement / Re: X2 Minimill cnc'd

« on: February 25, 2016, 08:29:18 AM »

  West Coast Florida, South Venice.  We're Always Open.

15

General Mach Discussion / Re: Input Piin Problems No Auto Find

« on: February 22, 2016, 11:13:14 AM »

Hi All,
Just checked the voltage again and found .5 volts on 2=3 4=5 6=7 my mistake from yesterday ,and 4.38 volts on 13=12=15=10. Still am not able to use the input 13 or the others to use the probe. Is this voltage TOO high from the PVC to use.

16

General Mach Discussion / Input Piin Problems No Auto Find

« on: February 21, 2016, 06:45:05 PM »

Hi Everyone,
Having a problem with the inputs to select E-Stop, Probe. It seems as though the E-Stop will work without checking the box or port# or pin# and active click, but flashes and toggles to run Mach or put into E-stop. Work's either way. I am running a Camtronics  Controller and had a problem yesterday about loosing the whole stepper setup and contacted Dan and he walked me through what I could have a problem with. Thanks Dan. Come today it started all over again input pins, and probe not working. I pulled the top of the controller off and did under power NOW to see what might be happening, and found that the gecko's 201's are pulling 0.04 volts on pins 2,3 4,5 6,7 and will jog and run a GCode. Fine. Now while in there I took a reading of the Pins 10 , 12 , 13 , 15 , and they read 4.2 volts. Quite a difference. I tried to get pin 13 to use the probe, and it will not work, however I can click on the Z- button and it will move slow ,but not stop as the wire is touched to activate the plate. CRASH!  In diagnostics screen, inputs are lit green from left to right 7 lit and no more on the top line. Using the auto find it is useless, as it won't work even on trying to set the E-Stop. Replaced the PP Cable and made sure it is Straight through, and it is. At this point I don't know what else to do. Anyone have any ideas as to what I can try next, Machine is grounded to the PC and PC is GRD to the controller and My GFI is GRD to the house wiring and test's OK. Also plugged in a regular outlet and same results. This Really has me Baffled .   
             Hank S.

17

Bargain Basement / Re: X2 Minimill cnc'd

« on: February 16, 2016, 07:38:54 PM »

Hello All,
I have come to the conclusion that the stepper motors are no long available for the Mini Mill, and have been donated to the other machine build that I had mentioned in a previous post that they would end up there. Mill is still FOR SALE, and will be put on the back burner. I have a set of Linear rails, that and with some down time, I might fabricate on the machine. Pick-Up is still the same, considered the costs, TOO much to box and ship. Weight and Packaging and Four boxes are just not going to happen, Outrageous Price's, and also will be asking $300.00 USD or Best Offer Considered, along with all the rest of the parts and pieces that were offered before at no extra cost.  Thanks Again.

18

Bargain Basement / Re: X2 Minimill cnc'd

« on: November 28, 2015, 05:53:25 PM »

Hi All,
Hope You All had a Peace Full, and Thank Full, Thanksgiving. 

19

Bargain Basement / Re: X2 Minimill cnc'd

« on: October 31, 2015, 11:42:07 AM »

BUMP;   All these look's, and no Offer, or Suggestion!

20

Bargain Basement / Re: X2 Minimill cnc'd

« on: October 03, 2015, 01:56:28 PM »

Hi All,
Sorry about being away from this post as I had to have a urgent medical situation to attend to, still recovering. I think I need to lower the price as I now am looking at some room to get so I can move around in the shop, as soon as I recover. That said I now am ASKING $ 400.00 for the mill, AS IS, and all the extra parts Included, PLUS, anything that you see you can use, ie. extra dc motors, controllers, and a piece of Roton ball screw and nut, which I'll cut, xl belts. Still have to have you pick this up, or let's see what we can do. I hate to not have the mill run before you buy, but if you have a reasonable solution, I'm open to the suggestion.  Thanks   Hank S.