Messages

31

Show"N"Tell ( Your Machines) / Re: Chiron FZ12 on its way sometime soon(ish)

« on: November 04, 2012, 09:09:59 AM »

Any one after a 4th axis have this for sale on eBay item no: 281012873231

http://www.ebay.co.uk/itm/281012873231?ssPageName=STRK:MESELX:IT&_trksid=p3984.m1555.l2649

John.

32

Show"N"Tell ( Your Machines) / Re: Chiron FZ12 on its way sometime soon(ish)

« on: November 04, 2012, 09:04:10 AM »

Hi Mark yes 6sc610 drives rod 456 500ppr encoders and heidenhain tnc 355b control.

John

33

Show"N"Tell ( Your Machines) / Re: Chiron FZ12 on its way sometime soon(ish)

« on: November 04, 2012, 07:14:02 AM »

Hi Hood yes box ways. It has encoders on the ball screws x and y the z encoder is on the motor.
The motors are Siemens 1ft 5066 3000 rpm not sure on the nm rating but they are geared 2:1 with pulleys. 15m/min rapids x and y and 10m/Min on the z.

John.

34

Show"N"Tell ( Your Machines) / Re: Chiron FZ12 on its way sometime soon(ish)

« on: November 03, 2012, 10:44:10 PM »

Back end!

John

35

Show"N"Tell ( Your Machines) / Re: Chiron FZ12 on its way sometime soon(ish)

« on: November 03, 2012, 10:39:50 PM »

Pic of carosel and bed.

John.

36

Show"N"Tell ( Your Machines) / Re: Chiron FZ12 on its way sometime soon(ish)

« on: November 03, 2012, 10:37:25 PM »

Smaller pic hopefully 

John

37

Show"N"Tell ( Your Machines) / Re: Chiron FZ12 on its way sometime soon(ish)

« on: November 03, 2012, 10:34:56 PM »

Ok thanks Brett Ill try the smaller size.

John

38

Show"N"Tell ( Your Machines) / Re: Chiron FZ12 on its way sometime soon(ish)

« on: November 03, 2012, 10:26:37 PM »

A few pics!

John

[attachment deleted by admin]

39

Show"N"Tell ( Your Machines) / Re: Chiron FZ12 on its way sometime soon(ish)

« on: November 03, 2012, 10:03:02 PM »

Looks good Hood. I have a similar machine a Beaver Partsmaster. Same configuration but the tool carosel is at the side of the bed.

I know that Beak Bain do replacement way covers for many different machines..I've bought from them before, very good service, they have a library of discontinued way covers that cover a wide spectrum..they might have something..

John.

[attachment deleted by admin]

40

Galil / Mitsubishi MR J2 with Heidenhain

« on: October 06, 2012, 09:46:07 AM »

Hi,

I know this is not a Mach3 topic but I know there are a good few Mitsubishi users on this forum!

I have technical question on the Mitsubishi MR J2 drives. If I use the encoder pass through from the CN1A socket what is the spec on the signal. I presume its  square wave. I have a Heidenhain controller that requires a sine wave 8-14 ua signal from the encoders which are incremental Rod456 Heidenhains at the moment but was looking at fitting these MR J2 Mitsubishi drives and using the pass through to the Heidenhain.

John.