Hello Guest it is December 06, 2021, 09:02:16 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - manmeran

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 »
61
Show"N"Tell ( Your Machines) / Re: My Big Project am I crazy
« on: September 03, 2010, 08:37:00 AM »
thx for reply
i use Yaskawa C A C R-S R 15BC about 1.5KW http://www.yaskawa.com/site/dmservo.nsf/%28DocID%29/TKUR-5TAKRN/$File/TSE-S800-2.2.pdf
Quote
do you need full drive output power?
no

yes, i check galil product.
the new product is very expensive,for example "4-axis Ethernet" about 2295$
now another question:
i hear about Dynomotion(kflop) controller:
- 200MHZ DSP controller
- USB 2
- support 8-axis
- analog servo control
- low price
 ...

what different between this type controller and Galil ?
This price difference over what is the topic?

Amir
 

62
Show"N"Tell ( Your Machines) / Re: My Big Project am I crazy
« on: September 02, 2010, 05:34:20 PM »
i read all comment and now i have two question :

1-about 3-phase > can we run 3-phase servo driver with single phase ? for example old Yaskawa
2-about isa        > This bus is outdated in Most motherboards .How you use it ?

Amir

63
General Mach Discussion / Re: Smoothstepper and probing, home and THC
« on: September 02, 2010, 03:59:47 PM »
Quote
1/2 second delay
i think this time is very long.
i build card modbus and speed refresh is about 70ms .if i have free time, 'll Test it

Amir

64
General Mach Discussion / Re: Smoothstepper and probing, home and THC
« on: September 02, 2010, 07:57:44 AM »
for connect THC to mach3

Amir

65
General Mach Discussion / Re: Smoothstepper and probing, home and THC
« on: September 02, 2010, 07:45:28 AM »
very thx for information
A proposal:
Can we use the Modbus?

Amir

66
General Mach Discussion / Re: Smoothstepper and probing, home and THC
« on: September 01, 2010, 01:20:16 PM »
Quote
THCs not working with smoothstepper and I think I understand why

Why ?  ;D

Amir

67
Show"N"Tell ( Your Machines) / Re: The Laser Project.
« on: September 01, 2010, 04:36:51 AM »
i agree for GALVO head  ;D ;D

Amir

68
Show"N"Tell ( Your Machines) / Re: X machine-Like
« on: September 01, 2010, 03:56:07 AM »
with Gas spring

Amir

69
Show"N"Tell ( Your Machines) / Re: The Laser Project.
« on: September 01, 2010, 03:54:22 AM »
Tweakie
is it possible tell price?

Amir

70
Show"N"Tell ( Your Machines) / Re: X machine-Like
« on: August 31, 2010, 12:58:27 PM »
Nice visual effect on the last photo.

Photoshop

Amir

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 »