Hello Guest it is March 28, 2024, 09:54:07 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - manmeran

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 »
11
Show"N"Tell ( Your Machines) / Re: The Laser Project.
« on: August 15, 2011, 03:55:28 AM »
Thanks Tweakie
about your cnc : ball screw driver or belt driver ?
in laser mode : how much max feedrate if we use belt driver for motion ?

Amir

12
Show"N"Tell ( Your Machines) / Re: The Laser Project.
« on: August 14, 2011, 01:00:44 PM »
i have a idea for build Magnet
by Air Valve Solenoid, magnet segment.

Amir

13
Show"N"Tell ( Your Machines) / Re: The Laser Project.
« on: August 14, 2011, 10:50:36 AM »
hi Tweakie
Very interesting.
is it possible tell about time for last photo(dog) with mangnet Method ?
and pls dimension ?

thx
Amir

14
General Mach Discussion / Re: Long pierce delay
« on: June 30, 2011, 11:54:06 AM »
you check this parameter if you set pierce delay to 0 in sheetcam :
Config / Port and pin /spindle setup /General parameters

Amir

15
Modbus / Re: Modbus and Timing
« on: May 03, 2011, 10:19:32 AM »
hi peter
i have some questions about this thread.
i attach my configuration and now

1-about refresh rate,i used two configuration :
   Cfg0 and Cfg1
   i set refresh rate to 25 and According to You ,is about 40ms .
   mach3 send this algorithm : 01 02 00 00 00 10 79 c6  01 10 00 00 00 07 0e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 05 6f
   This algorithm is consecutive ? OR is similar this : 01 02 00 00 00 10 79 c6---(40ms delay for reply)--- 01 10 00 00 00 07 0e 00 00 00 00 00 00 00 00 00 00 00 00 00 00 05 6f---(40ms delay for reply)---
   please explain .

2-you say about timeout :
Quote
It is the time between sending a request and receiving a reply
  then should Timeout < refresh rate
   Is this correct?

16
Quote
drives would be +-10volts analogue so you would need a $1000.00 motion board
you can use YAPSC for this purpose. Cheap and reliable

Dear JH
is it possible ask about price for lathe ?
Approximate price What is it?

Amir

17
Show"N"Tell ( Your Machines) / Re: Bridgeport is getting an overhaul
« on: March 01, 2011, 04:57:18 AM »
thx hood
i see you dont used from pico mobo ;)
i think this series is mini itx.

Amir

18
Show"N"Tell ( Your Machines) / Re: Bridgeport is getting an overhaul
« on: March 01, 2011, 04:38:03 AM »
pls link for manual

Amir

19
Show"N"Tell ( Your Machines) / Re: Bridgeport is getting an overhaul
« on: March 01, 2011, 04:18:19 AM »
thanks Hood for sharing this Experiences.
i have a question about servo spindle Driver .
Whether this is a three phase driver?

Amir

20
Show"N"Tell ( Your Machines) / Re: The Laser Project.
« on: December 14, 2010, 08:47:38 AM »
fantastic

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 »