Messages

1

Show"N"Tell ( Your Machines) / Re: 1997 DYNA MYTE DM4800 VMC to Mach3 Conversion

« on: October 12, 2011, 05:24:50 PM »

Hi Amir
I'm using the older 2100 series which is on Ethernet. I would recommend an econo series for a new purchase. The latest accellera is the best card if money is no object.
John.

i think for this time , Kflop is better . The same performance and lower price .
What do you think?

Amir

2

Show"N"Tell ( Your Machines) / Re: 1997 DYNA MYTE DM4800 VMC to Mach3 Conversion

« on: October 09, 2011, 02:39:31 PM »

john
about galil :Which series did you use?

3

Show"N"Tell ( Your Machines) / Re: 1997 DYNA MYTE DM4800 VMC to Mach3 Conversion

« on: October 09, 2011, 10:56:08 AM »

hi John
do you have any experience with Galil card+mach?
do we can to compare it with Meldas?

Amir

4

Show"N"Tell ( Your Machines) / Re: 1997 DYNA MYTE DM4800 VMC to Mach3 Conversion

« on: October 08, 2011, 02:33:49 PM »

the crash result in axis is for example :breaking tool (in addition,Finally drivers can stop axis with fault signal)
but in toolchange this result is very big and maybe Horrible accident
Amir

5

Show"N"Tell ( Your Machines) / Re: 1997 DYNA MYTE DM4800 VMC to Mach3 Conversion

« on: October 08, 2011, 02:23:42 AM »

fot toolchange if you can use PLC, i think is better and safer
mach run in windows and it not safe %100

Amir

6

Show"N"Tell ( Your Machines) / Re: 1997 DYNA MYTE DM4800 VMC to Mach3 Conversion

« on: September 16, 2011, 11:09:09 AM »

this machine made in 1997 . do you test rail for wobble and ballscrew for backlash?
Amir

7

Show"N"Tell ( Your Machines) / Re: 1997 DYNA MYTE DM4800 VMC to Mach3 Conversion

« on: September 08, 2011, 12:22:22 PM »

woow .very interesting
I always love your changes on the machine.
Amir

8

Show"N"Tell ( Your Machines) / Re: Bridgeport is getting an overhaul

« on: September 07, 2011, 05:23:26 PM »

The servos encoder have 2000 line (8000 counts per rev) and the gearing on the axis is 2.5:1 with 5mm pitch screws so resolution will be 0.00025mm and I am hoping to get the tuning so I have a following error of 20 counts/20mS so that would mean the axis would trip if it was ever 0.005mm out of position.
Hood

If you have been reached 5um accuracy then i must say congratulations and happy for you.
Amir

9

Show"N"Tell ( Your Machines) / Re: Bridgeport is getting an overhaul

« on: September 07, 2011, 04:18:34 PM »

yes
do you used c5 ballscrew in this machine?
and pls brand?
Amir

10

Show"N"Tell ( Your Machines) / Re: Bridgeport is getting an overhaul

« on: September 07, 2011, 04:06:41 PM »

hi Hood
Please talk about the accuracy in your machine.

Amir