Hello Guest it is March 29, 2024, 09:46:35 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - vicsrc

Pages: 1 2 »
1
General Mach Discussion / Re: Mach 3 machine coordinance
« on: April 03, 2014, 12:09:10 PM »
I have tried the way you describe and it does not work
When I zero mt dro's and hit ref home the dro starts counting and never stops/100,000 plus
before I get to the mach coord button






 

2
General Mach Discussion / Mach 3 machine coordinance
« on: April 02, 2014, 08:06:02 PM »
I would like to find a way to zero my machine coordinance.
I have tried to ref all home  and that does not work.
I want to set my tool in a zero location on my table and the set machine coord. to that spot as zero.
How can I accomplish this so that my part zero and machine zero are the same?

3
General Mach Discussion / remote jog control
« on: March 01, 2011, 09:23:47 PM »
Is there a way to use a remote jog with Mach 3 and a xylotec 3 axis board?

4
General Mach Discussion / mach demo
« on: November 13, 2010, 09:27:15 PM »
i have the mach cd and I had a hard drive crash.
When I reload mach I cant get the license to show up when I put it into the mach folder how can I fix this?

5
Mach3 and G-Rex / mach 3 missing code
« on: October 02, 2010, 11:41:27 PM »
I have a problem with mach 3 missng code when it is supposed to drill holes.
I am cuttimg 2 ribs a large and a small.
Both have holes to be drilled but the smaller rib does not show the hole location nor does it show the path it is to take to the holes.
The large rib shows the path and holes, both ribs are generated from the same drawing and the smaller bib is scaled down from the smaller rib.
I have imported the drawing into 4 different cad programs to see if the hole show up or if some how they are no getting transfered when I save the drawings but they show up in all 4 drawings. I have included the file also.

 

6
Mach3 and G-Rex / Re: Mach 3 display screen size
« on: September 22, 2010, 11:16:01 PM »
Thank you for the screen but how do you make it run offline?
I check all my mach3 runs on my home system without a cnc connected to make sure they run ok before I try a actual cutting run.
vic

7
Mach3 and G-Rex / Mach 3 display screen size
« on: September 21, 2010, 10:40:34 AM »
I am using Mach3 with my laptop to run a cnc router.
Everthing works fine but the display is so small that I cant see what its doing.
Is there a way to increase the size of the picture in the display to make it easier to see?

8
FAQs / A axis for a 4 axis foam cutter
« on: August 17, 2009, 09:47:04 AM »
How do I setup and config my A axis to use on a 4 axis foam cutter?

9
Mach3 and G-Rex / How to ???
« on: August 15, 2009, 12:36:44 PM »
How do I use Mach 3 as a 4 axis foam wing cutter?
What has to be setup to accomplish this?

10
General Mach Discussion / I need help please!
« on: May 27, 2009, 07:53:24 PM »
I am trying to use Lazy cam and Mach 3 mill of a router that I made myself.
The problem I have is with the software that I am using but I dont know if ti is because I am using the trials version or what.
I need to contact someone that I can talk to so that I can explain what is going wrong.
It is too involved to try to explain it on the forum.
I will gladly call and pay for the call if someone is willing to help me with my problems
 
thank you in advance
vic

Pages: 1 2 »