Hello Guest it is March 29, 2024, 10:14:09 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - comet

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 »
11
General Mach Discussion / Re: Somebody please help me install an mpg wheel
« on: December 08, 2021, 07:23:29 AM »
need to be a bit carefull with that sometimes you can get interfearance from the motors if the 5v and 24v are ground connected.

12
General Mach Discussion / Re: MPG issue
« on: April 23, 2021, 04:18:43 PM »
well if im honest the best motion controller ive used is the mega cheap bit sensor usb 4 axis module, they just work with no issues,got pretty much everything you need , if it craps out(not happened on the 5 machines ive built with them yet) you just buy another.

13
General Mach Discussion / Re: MPG issue
« on: April 23, 2021, 08:46:09 AM »
Hi,

Quote
I have put an enquiry on the cncdrive forum but no help.

Are you surprised?

CNCDrive is the manufacturer of the UC300 but also the software UCCNC, which is a competitor to Mach.
I can't imagine why anyone at CNCDrive could get too excited by trying to help you when they have others
to help whom use UCCNC software.

Craig

I wouldnt mind betting the majority of cncdrive users use mach.
Plus its the users that give you the suggestions on there forum rather than the company.

14
General Mach Discussion / Re: MPG issue
« on: April 14, 2021, 07:24:18 AM »
Hi, I still dont have a resolution to this issue, I have put an enquiry on the cncdrive forum but no help.

15
General Mach Discussion / Re: MPG issue
« on: March 29, 2021, 12:59:32 PM »
thanks for the reply,yes thats working

16
General Mach Discussion / MPG issue
« on: March 28, 2021, 09:36:57 AM »
I am trying to get the 1x 10x 100x to work with the velocity of of an MPG on a uc300
I have set in hot keys triggers 1 2 3
I have tried associating jog increment 191 192 193,  and also tried step value 265 266 267  and it makes no difference at the wheel
The port monitor is showing the pins are changing at the selection via a rotary switch on the pendant.
and the axis change rotary switch is working.
  Any Ideas??

17
General Mach Discussion / Re: MPG x1 x10 x100
« on: March 08, 2021, 08:00:12 AM »
Hi Tps, thanks but that link seems broken?

18
General Mach Discussion / MPG x1 x10 x100
« on: March 08, 2021, 04:18:54 AM »
Hi,
 I am making another MPG pendant for my machine, This time i want to use a 3 position rotary switch
with  x1 x10 x100 to control the rate.
   Looking at the OEM codes to be associated with the input triggers, I cant work out which ones to use .
Any Ideas?

regards
 Tony

19
General Mach Discussion / Re: zero axis within program
« on: April 13, 2020, 05:49:38 AM »
That works a treat, exactly what I needed thanks.
Tony

20
General Mach Discussion / Re: zero axis within program
« on: April 12, 2020, 05:49:43 AM »

Cheers Graham I will try that. Why do you need to use caution? Any other Tips
Happy Easter !!
Tony

G92 but use with caution

Pages: « 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 26 27 28 29 30 31 32 33 34 »