Messages

861

LazyCam (Beta) / Re: No tabs

« on: May 19, 2008, 02:21:14 PM »

Hi, Willem

LC needs further work, The saving of Tabs would be nice, You can redo the tabs/update them, There sometimes hard to see.

Thanks, Chip

862

General Mach Discussion / Re: THC on/off button not working

« on: May 19, 2008, 01:28:24 PM »

Hi, Jon

On the Enable question, Maybe use an Enable Output to turn on the Plasma or Hight Control.

Chip

863

LazyCam (Beta) / Re: No tabs

« on: May 18, 2008, 10:51:07 PM »

Hi, Willem

Hears a pic with 2mm 4 places .4 mm thick Tab's, Didn't try to post them though.

Chip

864

General Mach Discussion / Re: THC on/off button not working

« on: May 18, 2008, 03:27:52 PM »

Hi, Jon

Edit: First try changing the Active Low State for Output 2, That could be it, But from what you've stated it's working correct with your Posted G-code  on & off ?

Never seen a button work with the Reset Flashing on startup, or you saying, If I don't use the button, It works after Reset with your Loaded G-code File. ?

Using ver.R3.041 hear, Have a Plasma cutter and wanting to hook it up, Interested in your home-made arc voltage sensing THC, You mentioned.

Hears a screen set that I added a Torch ON/OFF Button on the Diag. and MDI Screen's, You can Edit the code in this button with, Operator, Edit Button

Script, In Mach, Its setup now to turn Output 2 on/off.

The button works hear fine, But I'm not using ver 2.63. Give it a Try, Let me now.

Thanks, Chip

Do you use Skype or live in the US CA, PM your Phone #

865

General Mach Discussion / Re: THC on/off button not working

« on: May 17, 2008, 04:29:59 PM »

Hi, Fiero

Are you saying you need to put Mach in E-stop/reset flashing or close Mach down and start it backup again ?

Are you using an Enable pin, May need to change the Active Low state.

More info would help, Sorry you fel through the cracks with no response till now.

Chip 

866

LazyCam (Beta) / Re: move entitie to another chain in Lazycam

« on: May 15, 2008, 08:58:36 PM »

Hi, Willem

Try renaming you Lcam file name if it has been used before it won't upload/post hear.
Post the new dxf you created also.

What type of material are you cutting ?

Chip

867

LazyCam (Beta) / Re: move entitie to another chain in Lazycam

« on: May 15, 2008, 12:39:51 PM »

Hi, Willem

It would offset with a .5 tool, But not the 1.0 one, There are still some quarks in LCam.

The left wing quit offsetting hear now also, I guess sometimes you can't "Wing It".

BobCad even missed one feather cut, Had to edit it in.

Chip

868

LazyCam (Beta) / Re: Problems with Depth in Lazycam

« on: May 15, 2008, 12:34:01 PM »

Hi, Wasi

On the left select Project, Then click on folder/layers containing your chain's, The bottom window will change to Layers view, You should see Cut Depth value there, If it's incorrect change it and click on Set Layer, Should do it, Don't forget the minus sign " - ".

Also have you set the Tool Per Pass in tool setup and saved changes and selected the Tool ?

Hope this Helps, Chip

869

LazyCam (Beta) / Re: move entitie to another chain in Lazycam

« on: May 15, 2008, 03:03:02 AM »

Hi, Willem

Hears a g-code file done with BobCad v22 cut depth -2.0, Tail feathers mouth & eyes  -.5, Rapids .1 & .5, F speed's .7487.

May need to change some of them.

Chip

870

LazyCam (Beta) / Re: move entitie to another chain in Lazycam

« on: May 14, 2008, 04:48:45 PM »

Hi, Willem

I worked on it some more, Hears an .LCAM file with everything but the right wing offset.

Load it and set your depth of cut and post, Will look at it later, Found some more unwanted lines.

Also a Tap file with no depth of cut.

Chip