Hello Guest it is March 29, 2024, 06:47:14 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Chip

631
LazyTurn / Re: LazyTurn
« on: November 14, 2008, 01:04:58 PM »
Hi, RC

Yes, Start z position works + & -, Stock, Profile "Dia.s" only seem to work if you increase the values, Errors if you try to set them below there Initial values.

Chip

Edit: Hears a dxf & tap file, You can adjust to a dia. closer to what you want.

632
General Mach Discussion / Re: Help getting set up
« on: November 14, 2008, 12:27:41 AM »
Hi, Beanprofit

Do you have a Pulse Freq. on the Diag. Page ?

Chip

633
LazyTurn / Re: LazyTurn
« on: November 14, 2008, 12:09:20 AM »
Hi, RC

I was able to reproduce the issue hear.

If you look into it further, There seem to be an Issue with the Stock Dia, Profile Dia and Posted G-code Diameter, Values.

Final Part should be 2.00 (R 1.00 x 2=2.00), G-code shows ( R 1.3225) or 2.645 Dia., Same as Stock Dir. Shown, I Think.

Pretty, Wild, Nice & Wonderful Program

Thanks, Chip

634
LazyTurn / Re: LazyTurn
« on: November 13, 2008, 09:52:09 PM »
Hi, Rich

I found that BobCad v22 DXF's are saving as ACAD R14 "AC1014" format, LazyCam/LazyTurn seems to be happiest with AC1006 (R10) & AC1009 (R11/R12) DXF's, Thanks for posting the File.

RC: Post your dxf and check the AC # as listed above.

Thanks, Chip

635
LazyTurn / Re: LazyTurn
« on: November 13, 2008, 01:03:42 AM »
Hi, Rich, Art & All

Looks like the generated Solid object isn't following the DXF's profile properly, Top Pic.

Solid object profile is being used to generate the Rough cut path, Bot. Pic.

Looking Nice Art, Thanks, Chip

636
LazyTurn / Re: LazyTurn
« on: November 12, 2008, 09:59:29 PM »
Hi, Rich

The King dxf I posted is about 2.3/4 inch's tall ( 2.750 Units), If I scale it up to 65 Units it loads fine.

The original King drawing was 250 units more or less, and loaded fine also, Would you post the working dxf you have.

Thanks, Chip

637
General Mach Discussion / Re: Anyone using Mach3 for Water jet cutting.
« on: November 12, 2008, 04:10:43 PM »
Hi, Jim

You need to configure the Mach3Mill Profile the same as you did the Plasma Profile, Ports, Pins, Motor Tuning, Ect......

They have separate "XML" Files.

Have a IR Water Jet 5' x 10' running Mach3, Work's Nice, Don't use it much.

Been using LazyCam and offsetting lines as you have.

Chip

638
LazyTurn / Re: LazyTurn
« on: November 12, 2008, 03:25:23 PM »
Hi, Art

This King was about 250 units long and loads fine, When it's scaled to 2.50 units it causes open-gl errors.

Pic & Dxf Att.

Thanks, Chip

639
LazyTurn / Re: LazyTurn
« on: November 11, 2008, 11:51:42 PM »
Hi, Marcel

Yes it works in windows XP.

Chip

640
LazyTurn / Re: LazyTurn
« on: November 11, 2008, 08:26:26 PM »
Hi, Art

Some DXF tests with 10-2, BobCad,v18,v21,v22,Rino v2.0, TurboCad v8.1, All are working Much better now.

Hear's a Ellips with no leadin's it misses left half rough cut paths, If you add leads, It loaded and I was able to get a full cut path with allot of opengl overflows along the way.

Have a fiew others with issues, But all-n-all, Wow this is Nice.

Thanks, Chip