Messages

581

LazyTurn / Re: LazyTurn

« on: December 14, 2008, 08:07:02 PM »

Hi, Art

Have a question, Can the Yellow marker ref. the X Zero point, Then Green marker would show cut start point as drawing shows hear.

As it is there is a disagreement in the value, The Blue marker shows part Diameter from Y Zero point.

Hope this makes sense, Chip

582

LazyCam (Beta) / Re: Lazy Cam dfx issue

« on: December 14, 2008, 12:34:11 AM »

Hi, Stitcher

Your file loaded & worked fine hear.

In Setup, Load Options, Dose it look like this.

Thanks, Chip

583

LazyCam (Beta) / Re: Lazy Cam dfx issue

« on: December 14, 2008, 12:14:32 AM »

Hi, Stitcher

Did the one I sent you load as sent and is the one you posted the one your having problems with now ?

Try saving in ver. 14, If that doesn't work reinstall LazyCam.

Thanks, Chip

584

LazyCam (Beta) / Re: Lazy Cam dfx issue

« on: December 13, 2008, 11:36:50 PM »

Hi, Stitcher

Post your dxf, Hears one to try.

Chip

585

LazyTurn / Re: LazyTurn

« on: December 12, 2008, 12:31:41 AM »

Hi, Art

Need to think on that idea for awhile.

Hears a cleaner file with 0.0001 overlap in yellow causing 1/2 the profile not to load and a file with ii fixed, Seems to be very small overlap's.

Edit: Tap & Pic's

Thanks, Chip

586

LazyTurn / Re: LazyTurn

« on: December 11, 2008, 09:34:11 PM »

Hi, Russ

Thanks Russ for the Picture, Well I did find a cad that show's them, Show's them as 0.0002" long, Intersection of Arc/Line,.

This file was from a cad/cam generated Offset and shows clean lines/arc's in 2 cad programs hear, Zoomed all the way in.

Edit: It's a tolerance issue, Cad, Cam and Accuracy, Balancing Act.

Thanks, Chip

587

LazyTurn / Re: LazyTurn

« on: December 11, 2008, 05:48:55 PM »

Hi, Art

This one is fine, Something to compare to.

Thanks, Chip

588

LazyTurn / Re: LazyTurn

« on: December 11, 2008, 05:28:00 PM »

Hi, Art

Hears a dxf problem file, Loads fine on my other Cad software.

In LazyTurn it's not scaled correct.

Edit: This file will load in LazyCam Turn and post sii Pic's in next Post, Last 2 Pic's.

Art, Your statement: ( By the time LazyTurn is complete, I will be very well armed to tackle some of these type of issues in LazyCam
which suffers greatly from tolerance issues. These sort of notifications therefore go toward educating me on the issues,
and even if they sound kinda crazy at times, they actuall do have their place in the scheme of things.)

Your statement is so true, LazyCam Mill....Turn, Were getting very close, Just some final bug's for the most part, Turn may have had some additional technical issues.

But as a overview are very Nice !!

Thanks, Chip

589

LazyTurn / Re: LazyTurn

« on: December 10, 2008, 01:30:57 PM »

Hi, Mick

Make sure it's in the C:\Mach3 "main" Folder and you start it there, After you un-zip it you need to copy it there.

Edit: LazyCam 3.00.2 Update    http://www.machsupport.com/downloads.php  Then install the latest up-date as above

Hope this Helps, Chip

590

LazyTurn / Re: LazyTurn

« on: December 09, 2008, 10:01:09 PM »

Hi, Art

Very....Very Nice, Not needing to translate all these numbers around is Fantastic, It was driving me crazy.

Jumping to end cutting, With a 0.0001 offset in Y(X) value, The Rt end finish should be no more than normal clean-up work on part's and after the rough/finish pass is implemented it will be nice. Pic below.

Thinking down the road a little more, If you made Y= 0+values as they are (outside cut's) and Y= 0- values (inside cut') and zero "no man's" zone, Drawing a part profile could be mirrored  for ether ?

Thanks, Chip