Hello Guest it is June 13, 2024, 10:51:28 PM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.


Messages - Chip

521
LazyTurn / Re: LazyTurn
« on: January 01, 2009, 12:41:10 PM »
Hi, Hank

Post the .DXF file your having problems with, We can't give you much help without It.

Chip

522
LazyTurn / Re: LazyTurn
« on: January 01, 2009, 12:01:22 AM »
Hi, Hank & RC

Got a little side tracked hear, Good to see it's working now.

I think most of the load issues in LT are fixed, There may be a few remaining though, Time will tell.

I now the connection tolerances are tight, But need to be that way for testing and developmental reason's, I'm Sure.

Hopefully they can be loosened up in the future.

Happy NEW YEAR to Everyone, Chip

 

523
LazyTurn / Re: LazyTurn
« on: December 31, 2008, 10:11:06 PM »
Hi Hank

Hear are some of the bad spot's marked and a dxf with them in it.

Chip

524
LazyTurn / Re: LazyTurn
« on: December 31, 2008, 09:18:10 PM »
Hi Hank

Got your file to load looking at it now, Ill post the proper format so RC can look at it. and explane the .dxf stuff in a bit.

Chip

525
LazyTurn / Re: LazyTurn
« on: December 31, 2008, 01:54:42 AM »
Hi, Simso

Most of the time you can open the same file in several programs and only run into trouble with trying to save a file with changes made to it, If others are open.

If it's not one thing it's another, Glad you got it going.

Chip

526
LazyTurn / Re: LazyTurn
« on: December 31, 2008, 12:51:54 AM »
Hi, Simso

Post your dxf that you saved in your acad 2009, Also check if there are any other dxf output options available for a ver. 12 or 14 dxf file's.

Chip

527
LazyTurn / Re: LazyTurn
« on: December 30, 2008, 07:11:13 PM »
Hi, Art

I was focusing a little to much on final pass profiles and the transition to that point with my question.

ooooooooo---ooooooo--ooo, A new button, Darn, Art it's not April.

Thanks, Chip

528
LazyTurn / Re: LazyTurn
« on: December 30, 2008, 04:08:00 PM »
Hi, RC

Are you using BobCad to generate that Profile in the post 2nd post back ?, If so what version.

Thanks, Chip

529
LazyTurn / Re: LazyTurn
« on: December 30, 2008, 12:57:13 AM »
Hi, Simso

Post one of your dxf's will look at it, Read through some of the post's and download some of the dxf's hear and load them in your cad program's.

If you post one of your dxf we can look at it to see the ACAD ver # ver 12,14, acad1009, acad1014 in the top of the dxt file as viewed with a txt editor like "note "pad usually work fine.

Chip

530
LazyTurn / Re: LazyTurn
« on: December 30, 2008, 12:37:38 AM »
Hi, Rich

The ragged view you last bottom post is just a "view" display issue in Mach3, You probably have the F speed set very high or in over-ride.

I see this quite often, It mostly shows up mid way in a lot of single axis g-code moves and isn't in the actual step or dir Output's.

Slow the F speeds down with Over-Ride and let me now.

Chip