Hello Guest it is September 21, 2023, 10:57:23 AM

Show Posts

This section allows you to view all posts made by this member. Note that you can only see posts made in areas you currently have access to.

Messages - Chip

LazyTurn / Re: LazyTurn
« on: January 02, 2009, 09:28:48 PM »
Hi, Art & ALL

ART: I agree with you comment's 100%, A branch in the road for sure, I see "3" ways to deal with it at the present time, Still thinking about it more.

1: Take into account for Lt,Rt & Center Cut Both Directions, (Which it pretty much "Could/Would do now") and leave your self a way to actually implement it in the future. (Do a little testing now to give you a "Good feeling" that, You could use the work done to this point, That it will work "OK", If you Find the need for a more diversified Tool Library in the Future. ( Like this one best)

2: Think about this and continue on while gathering more input and adding more experience's to your list, As we transition on to Final Pass code and beyond......... ( OK also)

3: Proceed on, Throwing Caution to the wind & Hope for the Best. (Don't care for this one at All.)

LazyTurn is as lazeeezy as they come and should remain that way, But leave yourself room for the, Notion that your comment that ("--Incompetence is an Art.. I'm mastering that "Art".") Is a State of Mind and is Actually an "ARTFORM" That has Led 10's of thousand's of Us to Master our CNC Hobbies to a Truly Lazy State.

Thanks, Chip

PS: I'll keep post'n-em as I see-em, "Possible Issue" is pretty Weak one. LOL {:-)>

LazyTurn / Re: LazyTurn
« on: January 02, 2009, 03:25:07 PM »
Hi, Art, RC & All

Hear it is, It only shows up with larger stock clearance settings

What ever you think Art, Just point it out.


LazyTurn / Re: LazyTurn
« on: January 02, 2009, 03:11:14 PM »
Hi, Vince

The settings RC posted should work for you, Just checked your dxf and don't get the mem leak issue.

Check that you have the latest ver. of LazyTurn installed, Hears a pic of the page you can find it on.


LazyTurn / Re: LazyTurn
« on: January 02, 2009, 01:42:24 PM »
Hi, RC & Art, All

That dose seem to fix the drawing for the most part.

But it brings to Light a possible Issue with the Left hand side of the rough profile not respecting the Tool width values and leaving the rough cut short on the left.

Hear are 2 Pic's, What do you think. ?

Thanks, Chip

LazyTurn / Re: LazyTurn
« on: January 02, 2009, 12:30:55 AM »
Hi, Art

I'd say LazyTurn is Hot.


LazyTurn / Re: LazyTurn
« on: January 01, 2009, 11:50:03 PM »
Hi, RC

I didn't do anything to the dxf and it looks fine hear. ?

Same thing hear with .5 Stock Clearance.

There are a few brakes in the dxf file.


LazyTurn / Re: LazyTurn
« on: January 01, 2009, 10:34:15 PM »
Hi, RC

Looks good also.


LazyTurn / Re: LazyTurn
« on: January 01, 2009, 10:02:28 PM »
Hi, RC

Seems fine hear, No brakes, Did you try any curvs.


LazyTurn / Re: LazyTurn
« on: January 01, 2009, 08:43:57 PM »
Hi, Hank

Why do all the Dxf's your posting have a .txt file name extent, Are you renaming them that way, ?, You should be able to post them with the .dxf's without any problem or changes needed.

The last one you posted seems to rough out just fine, It dose have some brakes in the profile though.


LazyCam (Beta) / Re: Trouble With Arcs
« on: January 01, 2009, 12:57:29 PM »
Hi, Aaron

Posting your .dxf file also help's us help you better as the issues most often start there.

Thanks, Chip